The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
Подобные документы
The study of structural changes during hot deformation metal during controlled rolling. The influence of preheating temperature and deformation degree on the size and shape of austenite grains. The definition of the polygonal structure of the austenite.
статья, добавлен 30.01.2017The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
магистерская работа, добавлен 14.02.2013Types of tool materials: from high-carbon steel to ceramics and diamonds, and their use as cutting tools in the modern metal industry. Cutting tool and its characteristics: hardness, strength. Achieving an acceptable tool life before replacing it.
статья, добавлен 26.04.2019The concept and functional characteristics of diamond-like films of amorphous carbon with a high concentration of carbon with SP3. The peculiarities of their practical use. Diagram of the coating, its physical and chemical properties, the benefits.
статья, добавлен 12.06.2015Creep and fatigue in polymer matrix composites. Stages, characteristics and deformation of creep. Mechanisms of creep. General creep equation. Dislocation, nabarro-herring, coble creep. Creep of polymers, of concrete. The molecular weight of the polymer.
курсовая работа, добавлен 02.02.2015The conductive nanocomposite films based on functional reactive copolymers and bifunctional alcohols. Creation multiwall carbon nanotubes. Dependence properties of the nanocomposites from the specific composite composition and obtaining conditions.
статья, добавлен 30.07.2016Processes of change of mechanical properties and microtexture of castings from gazars. Effect of monolithic areas formation inside the porous structure. Consideration of monolithic formations inside porous structure of gazar after annealing, x 50.
статья, добавлен 30.01.2016Analyzed the impact of long-term operation of gas pipelines, as well as natural stress concentrators on the physico-mechanical properties of welded joints of steel 17G1S. Regularities of the destruction of the material of welded joints of gas pipelines.
статья, добавлен 30.01.2016Study the structure of the coating made of composite material that contains wear-resistant components SiC-Al2O3. The use of a metallic binder based on iron in composite production. The properties of the obtained coatings with the steel counterface.
статья, добавлен 29.01.2016Properties and structure of hydrocarbons. Types and communication aromatics. The nature of the relationship between the carbon atoms. The methods of extraction and processing of oil. The use of the rectification columns for fractionating of raw materials.
презентация, добавлен 30.06.2014Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016The two main methods of mechanical assembly of plastic parts. Requirements for reliable mechanically bonded plastic joints. Special consideration for composites. The main advantages and disadvantages of adhesive bonding (gluing or glue bonding).
статья, добавлен 10.03.2019Aluminum can be considered green when its production and alloys processing are low-carbon (as well as associated with the reduced amount of other greenhouse gases, hazardous chemicals and environmental pollutants), include recycling of scrape and waste.
статья, добавлен 19.09.2024Carbon nanotube diodes as part of nanotechnology and a key component of the nanotechnology revolution, which could have major implications for the future. Nanotechnology is a discipline that deals with the design, production and manipulation of materials.
статья, добавлен 19.03.2024Demand for vehicles with a zero carbon footprint. Understanding the predictors of human behavior regarding the potential adoption or rejection of a technology. A comprehensive consideration of the possibilities of switching to low-emission vehicles.
статья, добавлен 20.07.2024The conductive nanocomposite films on the basis of reactionary copolymers received. The threshold of their percolation is determined. It was shown that its value depends on the size of specific surface of nanotubes and conditions of composite obtaining.
статья, добавлен 23.09.2016Experimental heat treatment of coal from the Shoptykol deposit of the Maikuben basin by carbonization, activation in a pilot laboratory unit. Analysis of the adsorption characteristics of the samples. Approbation of the obtained activated carbon.
статья, добавлен 28.12.2020Consideration the processes taking place in the metal pipe during prolonged use. Studing the complex physical and mechanical properties to assess the resistance to the destruction of the metal in the environment closest to the operating conditions.
статья, добавлен 30.01.2016The history of iron and Damascus steels through the eyes of ancient blacksmiths. Observation of color changes during heating and estimating of hardness by scratch tests, to have determined some key parts of the present-day iron-carbon phase diagram.
статья, добавлен 09.09.2012Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
статья, добавлен 14.09.2016Analysis of criteria for steels warping susceptibility under the thermochemical treatment. Study of value of the details warping during the quenching. Analysis of residual internal pressures in hardened layer and kinetics of austenitic grain growth.
статья, добавлен 30.01.2017The study of magnetron sputtered coatings on base AlN-TiB2(TiSi2). The structural composition, morphology coated materials. Features amorphous-like coatings AlN-TiB2(TiSi2) after annealing and their impact on physical and mechanical properties changes.
статья, добавлен 30.07.2016Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019Описание характеристик DH и REDA процессов вакуумного обезуглероживания, развиваемых на заводе Nippon Steel. Тенденция снижения содержания углерода в ультранизкоуглеродистых сталях, ее минимальный достижимый уровень. Снижение предела процесса DH.
статья, добавлен 19.11.2018