Determining the quantitative composition of an unknown gaseous fuel and combustion products from the measured process parameters in the fuel combustion process
There exists a wide range and a considerable potential of alternative gas fuel types. Uncertainty, flexibility of nonconventional fuels’ composition seriously limits the possible exploitation of these energy sources. Equations of chemical thermodynamics.
Подобные документы
Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016Information about the general state of technologies for the utilization of secondary energy resources and environmental resources. The essence of phase transitions in food production technologies. The possibility of creating energy-material circuits.
статья, добавлен 10.06.2022Formulation of the problem of calculating the scalar potential of the electric field in the axisymmetric disk, the material which has anisotropic permittivity. The method of successive approximations, a description of the potential of the electric field.
статья, добавлен 30.08.2016Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016The main advantages and disadvantages of well-known spiral drills with a multi-stage blade. It is described that the bridge, together with the steps adjacent to the grooves, is a small centering drill, performs centering and drilling during the process.
статья, добавлен 10.02.2021Consideration the mathematical model of process of pressing of seamless pipes. Effect on various forms of rolling shaping matrix. The nature of the formation of the deformation zone. Development of direct compression on a cylindrical mandrel pipe.
статья, добавлен 30.01.2016Experimental researches of improvement of technology of preparation of preparation Torasemide 5 mg / ml a solution for injections, a choice of a filtering material. Aseptic production conditions using sterile filtration and thermal sterilization.
статья, добавлен 01.12.2017Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
статья, добавлен 14.09.2016System for billet continuous caster’s mould heat engineering parameters monitoring. Formation of the internal heat transfer surfaces. Calculation the indicators: average heat flux density, overall heat exchange coefficient. Effective gas gap thickness.
статья, добавлен 30.01.2016Two sensor designs of metallic cylindrical resonator Coriolis vibratory gyroscope are analyzed in this work. Resonant frequencies computer modeling results are resented and on their basis gyroscope sensor geometrical parameters choice is validated.
статья, добавлен 14.09.2016Impact indicators coal shiites in the properties of the resulting coke. Coking process with the help of passive experiment. Effect of changes in the number of components of the coal charge on the quality of the coke at various technologies of sintering.
статья, добавлен 29.07.2016Modeling and principle of operation positioner power consumption in the direct mode of automated management. Evaluation of the use of the corrected function decline in electricity consumption in the automated control system of technological process.
статья, добавлен 28.02.2016Development and value of a robotic module, whose activity will be controlled based on the perception of the image obtained from a digital camera. Features and description of the process of creating an intelligent robotic module with a camera system.
статья, добавлен 28.08.2020The purpose of research was isolation and identification of Enterococcus species from raw milk and traditional dairy products and their biochemical properties were examined. Some biochemical and technological properties of the strains were determined.
статья, добавлен 28.05.2022Scientific justification for automated control method of optimal charge of pebble mill operating in series with a magnetic separator in the second stage of crushing in magnetic separating plants that process on iron ores with varying physical properties.
статья, добавлен 23.03.2016Increase in the use of hard, high strength and temperature resistant materials in engineering necessitated the development of machining techniques. Abrasive flow machining as process non-conventional machining processes. Magneto abrasive flow machining.
статья, добавлен 02.06.2014Studies of Heat and Mass of drying in the process for the production of slag gravel. Determination of the temperature of the thermal agent at the height of the layer of materials. The dependence of the velocity of the mass transfer of temperature zones.
статья, добавлен 24.02.2016Study of sorption of oil substances such as diesel fuels on zeolite beds. The use of clinoptilolite as a sorbent for the removal of oil substances. Preparation of synthetic zeolite, the addition thereof to improve the sorptive capacity of the zeolite bed.
статья, добавлен 24.02.2016The use of Calibration and Measurement Capability (CMC) to inform customers about quantities, ranges and uncertainty of the measurement laboratory. Problems for CMC tables for electrical quantity. The capabilities of accredited calibration laboratories.
статья, добавлен 14.07.2016Fast fatigue crack growth. The general content of nitrogen in the alloy system that limits fatigue life. Fragmenting the titanium sponge into small pieces and using various melting methods metals. Investigation of the Partially Melted Electrodes.
статья, добавлен 10.12.2018Design, develop Micro Air vehicle system provides a platform to support a very wide variety of missions for the small unit. Further miniaturization of electronics and sensors these vehicles to become even smaller and to operate in complex environments.
творческая работа, добавлен 18.01.2014Investigation of physical and mechanical properties of the cement using of barium-containing clinker and gypsum stone. Effect of additives of barium-containing sulfateferrite clinker gypsum stone. Longer hardening and limits and compressive strength.
статья, добавлен 23.02.2016Investigation of the mechanism of movement of working bodies vibroimpact classifier for the purpose of improving the efficiency and performance of mineral processing. Qualitative and quantitative analysis of the dynamics of working bodies of the pendulum.
статья, добавлен 24.02.2016Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019