Electroslag Refining of Titanium For the Removal of Nitrogen-Rich Inclusions
Fast fatigue crack growth. The general content of nitrogen in the alloy system that limits fatigue life. Fragmenting the titanium sponge into small pieces and using various melting methods metals. Investigation of the Partially Melted Electrodes.
Подобные документы
Synthesis of a batch of aluminum-doped titanium dioxide and testing the reaction of photocatalytic degradation of phenol in an aqueous suspension. Studies of the crystal structure of rutile anatase using XRD, XPS, Raman spectroscopy and EMF methods.
статья, добавлен 25.08.2017Model for calculation of nominal stresses in characteristic points of the surface fatigue crack to the tubular shaft in bending with rotation. Reasons for the decrease of the propagation velocity of cracks in the center and changing the geometry.
статья, добавлен 28.09.2016Consideration the influence of scandium on mechanical properties and heat-resistance of magnesium alloy ML10. Macrostructure of ML10 alloy with different scandium content. Sizes of microconstituents of heat-treated alloy with different scandium content.
статья, добавлен 30.01.2016The roller of the belt as the most important parts of the conveyor, being subjected to continuous stress both during operation and in stopping periods. Causes and weight percentage of failures due to fatigue. Sealing system with simple labyrinth.
статья, добавлен 27.12.2016Creep and fatigue in polymer matrix composites. Stages, characteristics and deformation of creep. Mechanisms of creep. General creep equation. Dislocation, nabarro-herring, coble creep. Creep of polymers, of concrete. The molecular weight of the polymer.
курсовая работа, добавлен 02.02.2015Analysis of the main causes of destruction of adhesive joints. Structural and technological stress concentrators, because of which cracks develop during operation. General characteristics of the resistance of adhesive bonding to failure at all stages.
статья, добавлен 30.04.2018- 7. The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
статья, добавлен 29.01.2016 Character of force of friction is investigated and set in nominally-immobile connections on the stage of nominal adhesion and to passing to skidding. The capacity of connections are given by the method of coating on the basis of fusible to the alloy.
статья, добавлен 27.07.2021Use of selective solvents in oil refining industry. Methods of cleaning oil raw materials. Technology of fractionation of extracts of phenol distillates, their chemical properties. Modeling the column of industrial extraction of petroleum products.
статья, добавлен 10.08.2018Research microstructure Rodent dental alloy based on Ni-Cr-Mo after casting in a vacuum furnace. Chemical analysis of crystallographic orientation and topography. Bold molybdenum carbides, eutectic-P and particles of aluminum oxide within dendrites.
статья, добавлен 23.02.2016- 11. Structural and electro-physical properties of heterogenous film materials based on refractory metals
Structural phase composition analysis of heterogenous film materials based on refractory metals is presented. A thermal activity nature of their conductivity was determined. Of investigation were estimated thermal resistance coefficient and energy.
статья, добавлен 30.07.2016 Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016- 13. Влияние температурных напряжений на накопление контактно-усталостных повреждений в колесе локомотива
Предложена методика учета влияния температурных напряжений, возникающих в колесах железнодорожного состава при колодочном торможении, на накопление контактно-усталостных повреждений в них. Методика программно реализована в модуле Rolling Contact Fatigue.
статья, добавлен 27.05.2018 Modernization of the transport system of the production system MPS 500. Creation of a new control program in the environment of the TIA portal. The main functions of the frequency converter. Investigation of the final state of the control cabinet.
статья, добавлен 26.08.2020Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Study of structure and properties of aluminum alloys treated with nanodispersed modifiers. Consideration of the classical theory of modification of melts. Creation of fine-grained structure of castings. Analysis of existing aluminum alloy modifiers.
статья, добавлен 21.04.2020Analysis of the use of aluminum alloys in the transport sector. Increased speed, safety, energy savings and reduced transport emissions thanks to aluminum. Ensuring a smooth ride and improved heat dissipation from the braking system using aluminum discs.
статья, добавлен 19.03.2024Investigation of physical and mechanical properties of the cement using of barium-containing clinker and gypsum stone. Effect of additives of barium-containing sulfateferrite clinker gypsum stone. Longer hardening and limits and compressive strength.
статья, добавлен 23.02.2016To separate simultaneous removal of mechanical impurities and water - the main tasks of filters. Analysis of the graphical representation of the piping system for pumping fuel and necessary equipment for the storage and dispensing of fuel operations.
курсовая работа, добавлен 29.03.2018Special supervisory control system responsible for the informative data acquisition about the current enterprise production and its control. The main SCADA. The general structure of SCADA. The Three main structure components modern SCADA-systems.
статья, добавлен 30.04.2019Analysis of the development of the basic methods of engineering the contact surfaces of tribological systems. Characteristics of the problems and prospects of development of technologies of creating surfaces of discrete-oriented structure of the system.
статья, добавлен 18.02.2016Production polystyrene composite films with small content of fullerenes (up to 1 %) by casting o-xylene solutions. A dependence of the glass transition temperature of the composite material on its composition. The adsorption capacity of polymer material.
статья, добавлен 30.07.2016Study of sorption of oil substances such as diesel fuels on zeolite beds. The use of clinoptilolite as a sorbent for the removal of oil substances. Preparation of synthetic zeolite, the addition thereof to improve the sorptive capacity of the zeolite bed.
статья, добавлен 24.02.2016Design, develop Micro Air vehicle system provides a platform to support a very wide variety of missions for the small unit. Further miniaturization of electronics and sensors these vehicles to become even smaller and to operate in complex environments.
творческая работа, добавлен 18.01.2014Development of methods for heat engineering tests of hydrodynamic pumps. Processes which occur in activator with water thermal hydrodynamic pump. Water flow speeds in a system. Gas bubbles are the product of centrifugal force effecting on carrier flow.
статья, добавлен 01.08.2016