Improving of manufacturing method of three-cone rock bits
Structure of three-cone rock bit with inserted hard-alloyed rock-destruction and protecting equipment, in which the chief components are marked. The minimally possible set of operators, which support qualitative performance of technological process.
Подобные документы
The food industry is unthinkable without fundamental science that is without scientific researches, highly technological production systems. The updating of technologies, the creating of new for future food technologies on fundamental science discoveries.
статья, добавлен 25.06.2018Scientific justification for automated control method of optimal charge of pebble mill operating in series with a magnetic separator in the second stage of crushing in magnetic separating plants that process on iron ores with varying physical properties.
статья, добавлен 23.03.2016The purpose of research was isolation and identification of Enterococcus species from raw milk and traditional dairy products and their biochemical properties were examined. Some biochemical and technological properties of the strains were determined.
статья, добавлен 28.05.2022Synthesis of a batch of aluminum-doped titanium dioxide and testing the reaction of photocatalytic degradation of phenol in an aqueous suspension. Studies of the crystal structure of rutile anatase using XRD, XPS, Raman spectroscopy and EMF methods.
статья, добавлен 25.08.2017The recent work on Micro Aerial Vehicles (MAV) at the Institute of Aerospace Systems. Basics of MAV Research. Flightmechanical simulation. Wind tunnel tests. Overall controller system structure. The inertial measurement unit. On-Board computer structure.
творческая работа, добавлен 18.01.2014Volumes of agricultural production of whole grain rice in Kazakhstan. Development of a technology for improving peeler for processing grain rice shals. Characteristics of polymeric materials used instead of rubber for rollers shelling machine A1-3RD-3.
реферат, добавлен 16.10.2017Study of structure and properties of aluminum alloys treated with nanodispersed modifiers. Consideration of the classical theory of modification of melts. Creation of fine-grained structure of castings. Analysis of existing aluminum alloy modifiers.
статья, добавлен 21.04.2020Defining of dimensional relationships where the aspect ratio. The building process for 3D microdevices. The features of creation surface energy high enough to maintain adhesion of the electroplated material until completion of the plating process.
реферат, добавлен 16.04.2017Обзор инновационной технологии от компании Smith Bits, StingBlade. Использование новой концепции буровых долот для перехода на новый уровень. Механические свойства режущих элементов, концепция дизайна и результат его применения в Пермском регионе России.
статья, добавлен 22.01.2019Особенности применения SPH-метода (Smoothed Particle Hybridization Method) для моделирования взаимодействия шин сверхнизкого давления с растительным покровом. Значения ширины шин для средств химизации при работе на почвах с низкой несущей способностью.
статья, добавлен 28.09.2016Способы оптимизации сложных технологических процессов. Понятие и применение e-Manufacturing в процессе проектирования и эксплуатации производственных систем. Разработка программного обеспечения для получения цифрового макета промышленного изделия.
эссе, добавлен 13.02.2023Processes of change of mechanical properties and microtexture of castings from gazars. Effect of monolithic areas formation inside the porous structure. Consideration of monolithic formations inside porous structure of gazar after annealing, x 50.
статья, добавлен 30.01.2016Analyzed the impact of long-term operation of gas pipelines, as well as natural stress concentrators on the physico-mechanical properties of welded joints of steel 17G1S. Regularities of the destruction of the material of welded joints of gas pipelines.
статья, добавлен 30.01.2016Introduction of new and innovative solutions for robotic devices. Application in production of the special individual decision on assembly operations. Execution of the assembly process with the introduction of two-handed robot in the assembly process.
статья, добавлен 28.08.2020There exists a wide range and a considerable potential of alternative gas fuel types. Uncertainty, flexibility of nonconventional fuels’ composition seriously limits the possible exploitation of these energy sources. Equations of chemical thermodynamics.
статья, добавлен 30.07.2016Consideration the processes taking place in the metal pipe during prolonged use. Studing the complex physical and mechanical properties to assess the resistance to the destruction of the metal in the environment closest to the operating conditions.
статья, добавлен 30.01.2016The establishment of unfavorable modes of operation of mining equipment under which there is an unstable position in space of the suction head during its descent to the bottom. The influence of hydrostatic pressure on the strengthening of the digging.
статья, добавлен 30.07.2016Systematization of lean production tools that can be implemented at enterprises. Possibilities of using each of the proposed tools to solve problems of Ukrainian business development. Determination of prerequisites for the formation of corporate culture.
статья, добавлен 09.07.2023Super ultrahard nanostructured and nanocomposite thin films. Preparation and industrial applications of hard and superhard nano-structured coatings on tools for machining (drilling, milling, turning), forming, stamping, injection moulding and the like.
статья, добавлен 30.07.2016Сущность технологии и техническая характеристика 3D принтера. Основные виды и преимущества 3D-печати. Краткое описание видов печати послойного напраления (Fusing Deposition Modeling) и послойного склеивания пленок (Laminated Object Manufacturing).
контрольная работа, добавлен 18.01.2017Analysis of the existing methods of the automatic regulation of the process of the drying of timber. Algorithm of the regulator of kiln drier. The need of regulating the drying process taking into account the characteristics of wood and drying agent.
статья, добавлен 28.11.2016The model of spatially distributed curing process of epoxy matrix polymeric composite. The model using the projections of Pareto points set on the 8-dimensional space of design variables. Сontrol synthesis for the closed mould curing of composite spar.
статья, добавлен 30.05.2017Analysis a lot of problems which constrain the transfer of diesel engines on "ecological" fuel and showing opportunities of manufacturing this fuel on Ukrainian enterprises. Evaluation of innovation taking in consideration environmental protection.
статья, добавлен 13.09.2016The concept, meaning and essence of a digital work, the use of technologies and equipment in the digitization of works. Features of converting a work into a digital format. Study of the main recommendations of the International Telecommunication Union.
статья, добавлен 17.09.2021Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016