On the distribution of stresses in circular infinite cylinder with cylindrical cavities
Nonaxisymmetric boundary value problem of elasticity theory for multiconnected body with cylindrical boundaries. Boundary conditions by the generalized Fourier method. The numerical analysis of stresses in the areas of their greatest concentration.
Подобные документы
Study of problems the sufficient conditions for the existence of solutions of linear nonhomogeneous impulsive boundary value problems with small perturbations when generating boundary value problem of impulsive has solutions for arbitrary right-hand side.
статья, добавлен 30.01.2017Model for calculation of nominal stresses in characteristic points of the surface fatigue crack to the tubular shaft in bending with rotation. Reasons for the decrease of the propagation velocity of cracks in the center and changing the geometry.
статья, добавлен 28.09.2016Two sensor designs of metallic cylindrical resonator Coriolis vibratory gyroscope are analyzed in this work. Resonant frequencies computer modeling results are resented and on their basis gyroscope sensor geometrical parameters choice is validated.
статья, добавлен 14.09.2016The key advantages of applying ultrasonic technology at the collection dairy. The general principles of measurement of liquids' properties by Ultrasonic standing wave resonator. The monitoring of the milk quality. The benefits of using cylindrical waves.
статья, добавлен 15.04.2015Joint with interference fit as third in total connections in engineering after a gap of cylindrical and threaded. The inductor for locomotive wheelset disassembly - one of the typical representatives of the induction coil for heating intricate parts.
статья, добавлен 14.09.2016In the test of diesel engine, because the performance test of multi cylinder engine with different configuration needs to be replaced, and there is a certain risk in the first test, while the single cylinder engine is more suitable for the research.
статья, добавлен 03.09.2024The developing of the numerical model of viscoelastic material using finite element method. The comparison of the obtained results with use of FEM software with experimental data. The calculation of the stress and strain state of the asphalt specimen.
статья, добавлен 29.09.2016The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
магистерская работа, добавлен 14.02.2013The present study is a mathematical modeling aimed at the dynamic force analysis of printed circuit boards in order to eliminate dynamic stresses to an acceptable level and ensure the strength and reliability of the printed circuit board design.
статья, добавлен 02.06.2022Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
статья, добавлен 14.09.2016The development of a new functional proposition, which uses the Poisson and Weibull distribution components, to simulate a functional U-shaped function. Estimating the effectiveness of the developed functional representation by numerical examples.
статья, добавлен 12.02.2019The role of piezoelectric transducers in electro- and hydroacoustics, where they are intended for radiation and reception of acoustic vibrations in air or aquatic environment. The use of monomorphic and bimorph elements for the manufacture of transducers.
статья, добавлен 30.08.2016Features of the two-phase model of the structure of keratin fibers. Estimation of the importance of critical and equilibrium stresses in the fibril, transfer of its stress to the matrix. Study of a possible connection between microfibrils and matrix.
статья, добавлен 30.05.2022Consideration the mathematical model of process of pressing of seamless pipes. Effect on various forms of rolling shaping matrix. The nature of the formation of the deformation zone. Development of direct compression on a cylindrical mandrel pipe.
статья, добавлен 30.01.2016Study of field distribution in structures such as a gold lattice, a graphene layer, and a silicon substrate. Conditions of maximum electromagnetic field distribution by these structures for the purpose of using them in photonics and electronics devices.
статья, добавлен 24.02.2024The use of the boundary values of parameters of mould displacement of the earth's surface and refining the workings of the design scheme to predict the trajectory of sedimentation. Determination of empirical coefficients of mathematical equations.
статья, добавлен 30.07.2016Cylinder shaped parts – one of the mostly used in printing presses. A new technology of strengthening and recovery of details based on vibration roll burnishing is offered in the article. Experimental work and scientific conclusions are described.
статья, добавлен 29.07.2016Analysis of finite element methods, numerical methods for solving engineering and mathematical physics. Obtaining analytical solutions for problems of complex geometry, loads and material properties. Tension rods, beams and other simple structures.
презентация, добавлен 20.10.2014Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Technological solutions that allow us to solve the problem of premature wear of the printing machines. A new technology of strengthening and recovery of details based on vibration roll burnishing is offered. Experimental work and scientific conclusions.
статья, добавлен 29.07.2016The length of the channel of the vibrating digging working body is substantiated by interaction with the body of the sugar beet root during its digging. A calculation scheme for the contact of the root crop with the working organ has been constructed.
статья, добавлен 15.09.2022The sustained propagation of combustion fronts in porous media is as a condition for the success of in situ combustion for oil recovery. The analysis of a method for modeling the propagation of combustion fronts in porous media. Problem of loss of a heat.
статья, добавлен 20.05.2013Creation and testing of a model of a diesel engine muffler. Plotting a pressure level diagram inside the device. Analysis of the distribution of the sound field. Assessment energy losses of exhaust gases. Estimation of the spectrum and octave bandwidth.
статья, добавлен 10.10.2024Determination of the rolling parameters that allow obtaining a bimetallic ribbed bar. Familiarization with the shape and dimensions of the round ribbed finished pass and of the bimetallic flat oval band obtained in numerical modelling - cross-section.
доклад, добавлен 24.12.2014