Influence of polysulfonamide tanlon fiber on resistance indicator of polythetrafluorethylene
Polytetrafluoroethylene as one of the promising polymers for tribotechnical purposes. The use of polysulfonamide fiber to increase the wear resistance of polytetrafluoroethylene under conditions of friction without lubrication in reciprocating motion.
Подобные документы
Rational modes of printing volumetric samples with a working thickness of the 316L powder layer of 40 μm to achieve a density of volumetric samples/ Determination of the density of metal samples by the metallographic method on an optical microscope.
статья, добавлен 19.03.2024The system of rest is energy-saving, with power supply from alternative energy sources intended for complex recovery of an organism in house conditions. Determine the effectiveness of panel modules on the level of stress. Application panel "Ananta 2016".
статья, добавлен 19.12.2017Experimental researches of improvement of technology of preparation of preparation Torasemide 5 mg / ml a solution for injections, a choice of a filtering material. Aseptic production conditions using sterile filtration and thermal sterilization.
статья, добавлен 01.12.2017Wind turbine concept with air duct. Influence of the exit area and entry area on aerodynamic characteristics. Designing a new model of Invelox. The need to install a curtain at the end of the air intake to change the direction of the air flow up, down.
статья, добавлен 08.03.2021The influence of the addition of soy flour processed by ultrafine grinding and irradiation on the quality of crispy baked goods. The wet soybean grounds were dried and ground in an ultra-fine grinding machine. Also set the ratio of beans to water.
статья, добавлен 02.06.2022Gathering of materials about a petroleum industry in a museum creates favorable conditions for their protection. The assemblage of materials is stored In a museum about the factory "Brothers Nobel". The oil extracted by brothers Nobel in 1894-1903.
статья, добавлен 03.03.2018- 82. Investigation of properties of the constant technological track, which is used in bridge agriculture
Mechanical properties of soil traces of a permanent technological track and their influence on the traction and traction properties of a bridge agricultural machine of a new design. The research was conducted using the provisions of the tractor theory.
статья, добавлен 30.08.2022 Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
статья, добавлен 21.12.2016Damage assessment of components of automobile and aircraft internal combustion engines, made of gamma titanium aluminides. Recommendations to prevent the negative influence of high temperatures in multilayer thin films on gamma titanium aluminides.
статья, добавлен 14.07.2016Economic and social challenges of breakthrough technologies in the context of Industry 4.0, Industry 5.0, their impact on sustainable development. Technologies for creating the Internet of Things. Potential characteristics of disruptive technologies.
статья, добавлен 30.11.2020Processes of change of mechanical properties and microtexture of castings from gazars. Effect of monolithic areas formation inside the porous structure. Consideration of monolithic formations inside porous structure of gazar after annealing, x 50.
статья, добавлен 30.01.2016Substantiation of expediency of enzymatic processing of canola meal for increasing its nutritional value. The role of enzymatic hydrolysis in reducing the amount of cellulose and hemicelluloses, increasing the amount of free phosphorus in rapeseed rape.
статья, добавлен 30.04.2018Problems of hardware configuration in systems for stabilization of information and measuring devices operated at vehicles of wide class in difficult conditions of disturbances action. Analysis of modern devices and units used in stabilization systems.
статья, добавлен 14.09.2016The conductive nanocomposite films based on functional reactive copolymers and bifunctional alcohols. Creation multiwall carbon nanotubes. Dependence properties of the nanocomposites from the specific composite composition and obtaining conditions.
статья, добавлен 30.07.2016Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016The model of the disperse material behavior under vibration in the hole of the dispenser based on the Navier-Stokes equations. The influence of the power factor on the movement of the product and the parameters of the hole on the vibrating dosing process.
статья, добавлен 14.09.2016Study of field distribution in structures such as a gold lattice, a graphene layer, and a silicon substrate. Conditions of maximum electromagnetic field distribution by these structures for the purpose of using them in photonics and electronics devices.
статья, добавлен 24.02.2024Investigation of obtaining diesteriv aliphatic dicarboxylic acid in the presence of aprotic catalysts - Lewis acids. Influence of catalysts on the technological indicators esterification process. Esterification process in the presence of aprotic acids.
статья, добавлен 23.02.2016The effect of casein-stabilized metal and metal oxide nanoparticles on the in vitro growth of Scoparia dulcis L. was studied. The effect of nanoparticles on callus induction, regeneration of shoots and roots was studied. Influence on the regeneration.
статья, добавлен 14.04.2022