Designing of a cavitation heat generator for heating water with a capacity of 10kw
Creation of a 3D model of the design scheme of the water heating and cavitation device and simulation in Hysys software. The main relationships between temperature, pressure and flow rate of the cavitation generator of the pulse hydrocycle unit.
Подобные документы
Models which adequately combine technological parameters with indicators of treatment quality have been designed for the cavitation cleaning processes of sewage from organic admixtures. Water of industry and public water use it is considered as sewage.
статья, добавлен 14.09.2016Research of influence of the electric discharge machining on change the properties of water. The formation of free radicals and hydrogen peroxide under the influence of cavitation is established, which leads to an increase in the whiteness of the wool.
статья, добавлен 21.12.2016The work of complex heat-recovery systems using water-hiting and air-heating heat-recovery exchangers was investigated. The combined use recovered heat to heat the return heat-network water, water of chemical water-purification system or combustion air.
статья, добавлен 22.04.2021Combined heating - a modern way of organizing the heat supply of the house. Use of independent sources of thermal energy. The advantages of using solar collectors. The principle of operation of the stove, fireplace insert. Types of combination boilers.
доклад, добавлен 14.03.2019Development of methods for heat engineering tests of hydrodynamic pumps. Processes which occur in activator with water thermal hydrodynamic pump. Water flow speeds in a system. Gas bubbles are the product of centrifugal force effecting on carrier flow.
статья, добавлен 01.08.2016Definitions and models of control in water supply and sanitation industry. Concession model of control sanitation industry in international practice. Condition of networks and evolution of model. Research limitations and future research directions.
дипломная работа, добавлен 13.11.2015Description and analysis of the characteristics of main problems to be solved in design of fixture. Examination and description of the main principles of work with the developed software to automate the modeling process and the design of the led lamp.
статья, добавлен 26.06.2016Development of a diagram and installation of a prototype of a two-flow heat pipe with the ability to regulate the parameters of the working environment. Using of the method of pulsed supply of liquid coolant to increase the heat transfer of a heat pipe.
статья, добавлен 14.12.2024The development of the modern world directly depends on the development of transport infrastructure. One of the types of transportation is pipeline systems, designed mainly for the delivery of liquid from one region to another (water pipelines).
статья, добавлен 14.02.2025The containment reservoir is where water accumulates during the flood season, one of the facilities that are absolutely essential for the proper functioning of every city. Use of this type of site as an open public space, regardless of water filling.
статья, добавлен 20.09.2021Analysis of TEC1-12705 and TEC1-12706 semiconductor refrigeration chip types with different hot heat dissipation conditions. Heat pipe heat dissipation test device for radiators. Effect of hot end heat dissipation conditions on cold end temperature.
статья, добавлен 10.10.2024Features the design of tooling for casting under pressure of zinc alloys. The problem that arise when designing a press-forms of analysis. Experiments to study thermal stability of materials, parts, equipment subject to cyclic thermo-mechanical treatment.
статья, добавлен 17.12.2016Wind turbine concept with air duct. Influence of the exit area and entry area on aerodynamic characteristics. Designing a new model of Invelox. The need to install a curtain at the end of the air intake to change the direction of the air flow up, down.
статья, добавлен 08.03.2021The traditional irrigation method, based on simple open canal systems, is extremely ineffective for managing critical and limited water resources. Conduct a qualitative assessment of irrigation water losses due to evaporation and system inefficiencies.
статья, добавлен 03.10.2021Joint with interference fit as third in total connections in engineering after a gap of cylindrical and threaded. The inductor for locomotive wheelset disassembly - one of the typical representatives of the induction coil for heating intricate parts.
статья, добавлен 14.09.2016Development of the composition of water-epoxy coating NIPU. Study the compatibility of components in water-based coatings. The optimum ratio of the components of the composition to obtain the necessary physical and mechanical properties of the coating.
статья, добавлен 29.07.2017Development of a managed system architecture with the possibility of full-scale parametric optimization. Systematization of the architecture of the conversion system by the example of the technological process of liquid heating. Software designer EFFLI.
статья, добавлен 30.10.2016Increase in the use of hard, high strength and temperature resistant materials in engineering necessitated the development of machining techniques. Abrasive flow machining as process non-conventional machining processes. Magneto abrasive flow machining.
статья, добавлен 02.06.2014Creation and testing of a model of a diesel engine muffler. Plotting a pressure level diagram inside the device. Analysis of the distribution of the sound field. Assessment energy losses of exhaust gases. Estimation of the spectrum and octave bandwidth.
статья, добавлен 10.10.2024Analysis of the flow characteristics of diode and the relationship between the fluid flow characteristics diode. The study of the flow characteristics of the flow diode. Definition of flow rate of each seal of air pump in each working condition.
статья, добавлен 24.02.2025Studies of Heat and Mass of drying in the process for the production of slag gravel. Determination of the temperature of the thermal agent at the height of the layer of materials. The dependence of the velocity of the mass transfer of temperature zones.
статья, добавлен 24.02.2016Research foaming effect, which can be the addition of zeolite in the asphalt mixture that causes the of the asphalt, better adhesion and ability lehkoukladalnist mixture. Characteristics of adsorbed water allocation as a function of time and temperature.
статья, добавлен 24.02.2016Developing of a photobioreactor design for wastewater treatment in which the application of new connections reduces material consumption for the manufacture of transparent flexible tanks, reducing labor costs for installation and dismantling of tanks.
статья, добавлен 10.07.2022Сопоставлены данные о гидродинамике реального потока смоделированного в программе SolidWorks Flow Simulation в эмульсоре вихревого типа, в центральной части камеры энергетического разделения которого, создается зона пониженного давления - зона кавитации.
статья, добавлен 02.01.2025Class of application of heat pumps in industry. Review of the carbon dioxide heat pump in the transcritical cycle of operation according to the expander-ejector scheme. Development of methods for selecting control valves for a given heat pump circuit.
статья, добавлен 02.02.2019