Use of magneto abrasive flow machining to increase material removal rate and surface finish
Increase in the use of hard, high strength and temperature resistant materials in engineering necessitated the development of machining techniques. Abrasive flow machining as process non-conventional machining processes. Magneto abrasive flow machining.
Подобные документы
Comparison of two non-conventional processes which are laser and photochemical machining. The formation of complex shapes in metal sheets. Chemical etching of the material for the manufacture of the desired finished product by a controlled corrosion.
статья, добавлен 03.12.2015Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
статья, добавлен 10.03.20193D printing (Additive Manufacturing Process, AM) is any of various processes used to make a three-dimensional object without the use of dies, molds or machining. The most basic, differentiating principle behind 3D printing. General principle modeling.
статья, добавлен 20.02.2019Super ultrahard nanostructured and nanocomposite thin films. Preparation and industrial applications of hard and superhard nano-structured coatings on tools for machining (drilling, milling, turning), forming, stamping, injection moulding and the like.
статья, добавлен 30.07.2016Research of influence of the electric discharge machining on change the properties of water. The formation of free radicals and hydrogen peroxide under the influence of cavitation is established, which leads to an increase in the whiteness of the wool.
статья, добавлен 21.12.2016Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019Development of methods for heat engineering tests of hydrodynamic pumps. Processes which occur in activator with water thermal hydrodynamic pump. Water flow speeds in a system. Gas bubbles are the product of centrifugal force effecting on carrier flow.
статья, добавлен 01.08.2016Rationale for the use of advanced technology for sewage treatment schemes dairies. Removal of insoluble organic matter by adding a flotation purification scheme. Using the immersed biofilter for a disk intensive degradation of organic pollutants.
статья, добавлен 13.08.2016Surface-polymer flooding (the so-called micellar polymer flow) as a potentially advanced oil recovery technology is more effective than polymer flooding. Surface-active interaction and compatibility of the polymer. Distinctions, drawbacks of the method.
статья, добавлен 06.05.2018The development of scientific and methodological bases of forming of structural and phase composition of alloys synthesized by the combined processes which consist of the metallothermic stage and SHS (self-propagating high-temperature synthesis).
статья, добавлен 07.09.2022Studies on the preparation of pasty high-filled compositions and evaluation of their rheological properties using a rotational visco-meter "Reotest-2" on the cone-plane system. Evaluation of sedimentation resistance of compositions and their flow.
статья, добавлен 30.10.2016In the article, high-temperature superconductivity is investigated and studied, and its promising paths are shown. One of these methods is the application of extreme pressures. In addition to hydrogen-containing materials, the article reflects the names.
статья, добавлен 10.10.2024Defining of dimensional relationships where the aspect ratio. The building process for 3D microdevices. The features of creation surface energy high enough to maintain adhesion of the electroplated material until completion of the plating process.
реферат, добавлен 16.04.2017Search for ways to reduce emissions of pollutants. Biomass as a composite material. Laboratory installation for glucose fermentation to ethanol. Study the concentration of xylose as a function of time. Process flow diagram of the synthesis of bioethanol.
статья, добавлен 23.06.2018Аналіз методики та результатів математичного моделювання з використанням пакету Flow Vision процесів течії в’язкої рідини в вузькому проміжку між циліндричним електродом-дротом та пласкою поверхнею заготовки при коаксіальній подачі струменю промивки.
статья, добавлен 11.10.2013Thermosetting plastics, their irreversible chemical reaction (polymerization), including the effects of temperature and time. Bringing the resin composition to a liquid state, forcing the liquid to flow into the cavity of the desired configuration.
статья, добавлен 10.03.2019The regularities of macromolecules behavior in the flow with longitudinal velocity gradient and manifested in this case effects of elastic deformations have importance in understanding the mechanism of anomalously high cutting power of water-polymer jet.
статья, добавлен 28.02.2016Types of tool materials: from high-carbon steel to ceramics and diamonds, and their use as cutting tools in the modern metal industry. Cutting tool and its characteristics: hardness, strength. Achieving an acceptable tool life before replacing it.
статья, добавлен 26.04.2019Analysis of the development of the basic methods of engineering the contact surfaces of tribological systems. Characteristics of the problems and prospects of development of technologies of creating surfaces of discrete-oriented structure of the system.
статья, добавлен 18.02.2016The use of metallic pigments with features of the geometry of the surface of printing materials. Functionality of the "Materials Editor" program and a group of parameters of geometric surface structures. Assessment of surface structures in the 3D system.
статья, добавлен 12.06.2023Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018