Effect of pumpkin seed flour, chestnut flour, and rosehip flour on wheat bread staling rate
The bread was made from type 500 wheat flour with the addition of pumpkin seed, chestnut or rosehip flour Bread staling was determined by measuring the deformation characteristics of the bread crumb. The total, plastic, elastic deformation of the bread.
Подобные документы
The influence of the addition of soy flour processed by ultrafine grinding and irradiation on the quality of crispy baked goods. The wet soybean grounds were dried and ground in an ultra-fine grinding machine. Also set the ratio of beans to water.
статья, добавлен 02.06.2022Creep and fatigue in polymer matrix composites. Stages, characteristics and deformation of creep. Mechanisms of creep. General creep equation. Dislocation, nabarro-herring, coble creep. Creep of polymers, of concrete. The molecular weight of the polymer.
курсовая работа, добавлен 02.02.2015- 3. The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
статья, добавлен 29.01.2016 Comprehensive analysis of allelic protein variants suitable for use in bakery products made from Iraqi wheat varieties, as well as biological evaluation of these varieties using a genetic source using a general method of qualitative grain selection.
статья, добавлен 18.03.2021Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
статья, добавлен 14.09.2016The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
магистерская работа, добавлен 14.02.2013The study of structural changes during hot deformation metal during controlled rolling. The influence of preheating temperature and deformation degree on the size and shape of austenite grains. The definition of the polygonal structure of the austenite.
статья, добавлен 30.01.2017Consideration the mathematical model of process of pressing of seamless pipes. Effect on various forms of rolling shaping matrix. The nature of the formation of the deformation zone. Development of direct compression on a cylindrical mandrel pipe.
статья, добавлен 30.01.2016Processes of change of mechanical properties and microtexture of castings from gazars. Effect of monolithic areas formation inside the porous structure. Consideration of monolithic formations inside porous structure of gazar after annealing, x 50.
статья, добавлен 30.01.2016Research foaming effect, which can be the addition of zeolite in the asphalt mixture that causes the of the asphalt, better adhesion and ability lehkoukladalnist mixture. Characteristics of adsorbed water allocation as a function of time and temperature.
статья, добавлен 24.02.2016The regularities of macromolecules behavior in the flow with longitudinal velocity gradient and manifested in this case effects of elastic deformations have importance in understanding the mechanism of anomalously high cutting power of water-polymer jet.
статья, добавлен 28.02.2016A method of determining the effective longitudinal elastic modulus for the composite material in the problem of longitudinal tensile composite. Unidirectional composite material with a hexagonal arrangement of fibers. The effective elastic modulus.
статья, добавлен 27.09.2016Characterization of elastic properties of saturated hydrocarbons and associates resinous-asfaltenovyh of compounds by simulating molecular dynamics. Evaluation of rheological behavior of heavy oil the elasticity matrix of transversely isotropic material.
статья, добавлен 27.07.2016Analysis of the flow characteristics of diode and the relationship between the fluid flow characteristics diode. The study of the flow characteristics of the flow diode. Definition of flow rate of each seal of air pump in each working condition.
статья, добавлен 24.02.2025The two main methods of mechanical assembly of plastic parts. Requirements for reliable mechanically bonded plastic joints. Special consideration for composites. The main advantages and disadvantages of adhesive bonding (gluing or glue bonding).
статья, добавлен 10.03.2019Search for ways to reduce emissions of pollutants. Biomass as a composite material. Laboratory installation for glucose fermentation to ethanol. Study the concentration of xylose as a function of time. Process flow diagram of the synthesis of bioethanol.
статья, добавлен 23.06.2018Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019Adding ginger extract to the technology of table margarine production. Expanding the margarine market range and extending its shelf life. The effect of adding an additive on an organoleptic characteristics of margarine, giving it a spicy taste and aroma.
статья, добавлен 14.12.2024Square Lead-Rubber Bearings with four lead plugs to round Lead-Rubber Bearings with one lead plugs and shorten the analysis time. Comparison of load-deformation relationship. Comparison of the change in the outer edge temperature of the laminated rubber.
статья, добавлен 10.10.2021Study the effects of man-made nano-additive on basic physical and mechanical properties of foamed glass. Use tare and flat glass as the main raw material. Investigation the effect of nano-additive on structural features of the resulting foam glass.
статья, добавлен 30.07.2016The peculiarity of studying the value of the protein-hydrogen index in the technology of milk production. Colorimetric and potentiometric methods of measuring pH in chemical and biological systems. Determination of basic acidity of dairy products.
статья, добавлен 22.08.2022Рассмотрение производственного инструмента Total Productive Maintenance. Сокращение потерь по эксплуатации оборудования. Алгоритм внедрения инструмента бережливого производства на предприятии. Самостоятельное обслуживание оборудования оператором.
статья, добавлен 11.02.2016Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016Methodical approach to the determination of key parameters of rotary positioning units intended for manufacturing technology and robotics. The applicability of the selected methodology for measuring selected parameters of the uniaxial positioning table.
статья, добавлен 26.08.2020