FDM ? LOM 3D ??????, ??? ??????????? ?????????? ????????????
???????? ?????????? ? ??????????? ?????????????? 3D ????????. ???????? ???? ? ???????????? 3D-??????. ??????? ???????? ????? ?????? ?????????? ?????????? (Fusing Deposition Modeling) ? ?????????? ?????????? ?????? (Laminated Object Manufacturing).
Подобные документы
The relation between the particles velocity and the deposition efficiency of material powders. A different approaches for calculating the critical deposition velocity. Computational fluid dynamics model. Critical particle velocity determination.
??????, добавлен 29.11.2016????? ?????????? ??????? Lean Manufacturing ?? ?????????? ? ?????????? ?????????. ?????????? ??????????????-???????????? ???????? ? ????????? ? ???????????? ?????????? ???????????? ?????? ??????? Lean Manufacturing ??? ???????? ???????? ????????????.
????????? ??????, добавлен 25.01.2013Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
??????, добавлен 21.12.2016- 4. The Impact Analysis of Breakthrough Technologies on the Development of Russian Oil and Gas Companies
Studying the process of developing and disseminating disruptive technologies. Additive manufacturing or 3D printing. Artificial intelligence and virtual reality. A glimpse into the future of science, technology and business - 35-year perspective.
????????? ??????, добавлен 11.09.2020 The manufacturing industry may be a key sector for the application of this technology, reduce the use of conventional energy sources, especially in the food industry located in the Andean region. Ecuadorian policies and regulations on renewable energy.
??????, добавлен 23.07.2021The present study is a mathematical modeling aimed at the dynamic force analysis of printed circuit boards in order to eliminate dynamic stresses to an acceptable level and ensure the strength and reliability of the printed circuit board design.
??????, добавлен 02.06.2022Identification of the distance of the shot and other circumstances in the case of a gunshot injury are among the key issues facing the forensic medical expert and of greatest interest to law enforcement agencies. The use of laboratoryinstrumental methods.
??????, добавлен 27.12.2023Square Lead-Rubber Bearings with four lead plugs to round Lead-Rubber Bearings with one lead plugs and shorten the analysis time. Comparison of load-deformation relationship. Comparison of the change in the outer edge temperature of the laminated rubber.
??????, добавлен 10.10.2021??????? ??????????? ??????? ??????????????? ?????????. ??????? ? ?????????? e-Manufacturing ? ???????? ?????????????? ? ???????????? ???????????????? ??????. ?????????? ???????????? ??????????? ??? ????????? ????????? ?????? ????????????? ???????.
????, добавлен 13.02.2023In recent decades, the phenomenon of globalisation has become increasingly pronounced, bringing opportunities and challenges for different businesses. Globalisation, defined as the process of integrating economies, cultures and societies across the globe.
??????, добавлен 17.12.2024Systematization of lean production tools that can be implemented at enterprises. Possibilities of using each of the proposed tools to solve problems of Ukrainian business development. Determination of prerequisites for the formation of corporate culture.
??????, добавлен 09.07.2023Motion systems as core technologies, as mechanical systems, like microelectronic manufacturing equipment, are required to achieve high speed and accuracy. The influence of the dynamics of a mechanical system on the quality of the position tracking syste
??????, добавлен 26.08.2020Structure of three-cone rock bit with inserted hard-alloyed rock-destruction and protecting equipment, in which the chief components are marked. The minimally possible set of operators, which support qualitative performance of technological process.
??????, добавлен 14.09.2016Analysis a lot of problems which constrain the transfer of diesel engines on "ecological" fuel and showing opportunities of manufacturing this fuel on Ukrainian enterprises. Evaluation of innovation taking in consideration environmental protection.
??????, добавлен 13.09.2016Comparison of thermal insulation properties of Sakhabult products with products of other manufacturers. Manufacturing of a dummy for monitoring the temperature difference inside sleeping bags and outerwear from natural fur of fur animals, deer and horses.
??????, добавлен 01.04.2021Consideration of the characteristics of semantic modeling. Analysis of passivity-based switching control for stabilization of wheeled mobile robots. Features optimal kinodynamic motion planning for 2D reconfiguration of self-reconfigurable robots.
?????, добавлен 09.04.2013Methodical approach to the determination of key parameters of rotary positioning units intended for manufacturing technology and robotics. The applicability of the selected methodology for measuring selected parameters of the uniaxial positioning table.
??????, добавлен 26.08.2020? technology for manufacturing composite materials - flocculants-coagulants on aluminum-silicon and iron-silicon base. The evaluation of the effectiveness of the developed flocculants-coagulants for cleaning of natural water and industrial wastewater.
??????, добавлен 11.01.2018The model is based on a regional convolutional neural network architecture that can identify and classify different types of damage, including those caused by natural disasters, accidents, or deliberate warfare attacks, such as shelling and bombardment.
??????, добавлен 12.12.2024The model is based on a regional convolutional neural network architecture that can identify and classify different types of damage, including those caused by natural disasters, accidents, or deliberate warfare attacks, such as shelling and bombardment.
??????, добавлен 12.12.2024Research of mathematical model of the process intrusion forming polymer products. Establishing a dependency on the angle of melt costs lifting screw injection unit in the material cylinder based on the geometric parameters of extrusion head and mold.
??????, добавлен 18.02.2016Test the tribological properties of lubricants as the main stage of assessing their suitability for use in friction. The scheme of the "cone - three ball" with the use of objects of simple geometric shapes to test different construction materials.
??????, добавлен 29.01.2016The development of a new functional proposition, which uses the Poisson and Weibull distribution components, to simulate a functional U-shaped function. Estimating the effectiveness of the developed functional representation by numerical examples.
??????, добавлен 12.02.2019The application of the YOLOv8 and ByteTrack real time object identification algorithms to accurately determine the number of individuals boarding and exiting buses. This study aims to determine the prevalence of stowaways on buses in Kazakhstan.
??????, добавлен 14.02.2025Description and analysis of the characteristics of main problems to be solved in design of fixture. Examination and description of the main principles of work with the developed software to automate the modeling process and the design of the led lamp.
??????, добавлен 26.06.2016