The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
Подобные документы
The basic connotation of electrical engineering and automation and intelligent technology, analyzes the electrical engineering and automation intelligent technology application in improving the level of system control, improve data processing accuracy.
статья, добавлен 24.02.2025Результаты разработок фирмы Bosch Rexroth. Гидравлические системы Load Sensing, в которых мгновенное давление нагрузки служит сигналом обратной связи для управляющего устройства. Применение системы LUDV (независимое от нагрузки распределение потока).
статья, добавлен 26.10.2010Analysis of TEC1-12705 and TEC1-12706 semiconductor refrigeration chip types with different hot heat dissipation conditions. Heat pipe heat dissipation test device for radiators. Effect of hot end heat dissipation conditions on cold end temperature.
статья, добавлен 10.10.2024Расчет элемента трубопровода при помощи Flow Simulation в пакете SolidWorks. Характеристика исследования влияния размеров и формы воздуховодов на равномерность воздушного потока и сопротивление в вентиляции системы охлаждения тяговых электродвигателей.
контрольная работа, добавлен 17.09.2015Using and improvement of qualities of products of oil processing. The process of obtain a water-soluble colloidal sulfur with seating stability, good solubility in water, high biological activity. Selection of conditions to receiving polymeric products.
статья, добавлен 11.03.2019Offered and analysed of the method of calculating the operating parameters of warping spools and mode of winding. A formula that is obtained allows to define relationship between the parameters of the threads wound on a warping spool and their pull.
статья, добавлен 29.11.2016Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Характеристика концепции производственного планирования, главной особенностью которой является возможность построения расписания работы оборудования в рамках всего предприятия. Изучение преимуществ и особенностей систем Advanced Planning & Scheduling.
реферат, добавлен 18.12.2014The developing of the numerical model of viscoelastic material using finite element method. The comparison of the obtained results with use of FEM software with experimental data. The calculation of the stress and strain state of the asphalt specimen.
статья, добавлен 29.09.2016The study of magnetron sputtered coatings on base AlN-TiB2(TiSi2). The structural composition, morphology coated materials. Features amorphous-like coatings AlN-TiB2(TiSi2) after annealing and their impact on physical and mechanical properties changes.
статья, добавлен 30.07.2016Search for ways to reduce emissions of pollutants. Biomass as a composite material. Laboratory installation for glucose fermentation to ethanol. Study the concentration of xylose as a function of time. Process flow diagram of the synthesis of bioethanol.
статья, добавлен 23.06.2018Aspects of the use of different types of alternative fuels that will ensure economic stability and reduce the harmful effects on the environment. Use in alternative fuel vehicles and advanced technology vehicles. Using batteries and electric motors.
статья, добавлен 03.09.2024Analysis of the flow characteristics of diode and the relationship between the fluid flow characteristics diode. The study of the flow characteristics of the flow diode. Definition of flow rate of each seal of air pump in each working condition.
статья, добавлен 24.02.2025Інформаційний аналіз методів та технологій для попередження утворення та видалення асфальтеносмолопарафінових відкладень на нафтогазопромисловому обладнанні. Дослідження віртуальної моделі струминно-кавітаційного генератора за допомогою модуля Simulation.
автореферат, добавлен 23.10.2018Reduce costs and increase durability of threaded connections. The relationship between the thermal treatment and the strength of the threaded connection. Compare the minimum tightening hermetic threaded connections three types of anaerobic adhesives.
статья, добавлен 28.09.2016Consideration of the characteristics of semantic modeling. Analysis of passivity-based switching control for stabilization of wheeled mobile robots. Features optimal kinodynamic motion planning for 2D reconfiguration of self-reconfigurable robots.
книга, добавлен 09.04.2013Assessing the development of the global economy and aerospace industry. Finding ways to reduce environmental pollution, energy consumption and flight costs. Increasing the thrust-to-weight ratio, safety and reliability of modern aircraft engines.
статья, добавлен 20.07.2024Прочностные характеристики пространственной трубчатой рамы спортивного автомобиля класса "Формула Студент". Проектирование рамы болида в программном продукте Solidworks Simulation в регламенте FSAE. Построение эпюр перемещений и запаса прочности рамы.
статья, добавлен 06.05.2018Estimation of energy release in mills of various types to understand the thermodynamic aspect of processes during mechanoactivation treatment. Modeling the motion of the balls of a mill and evaluating the generation of energy in the ball system.
статья, добавлен 07.08.2020The comparison of natural modes for the first and second transverse oscillation modes obtained by numerical simulation and finite element package of analytical calculation of the core model. The analysis waveforms for different values of the defect.
статья, добавлен 29.06.2017Анализ внутренних компонентов разрабатываемого противоударного планшета. Анализ методики создания эскиза печатной платы. Проектирование трехмерной модели модуля камеры. Симуляция падения корпуса планшета в программном комплексе SolidWorks Simulation.
дипломная работа, добавлен 29.06.2014Square Lead-Rubber Bearings with four lead plugs to round Lead-Rubber Bearings with one lead plugs and shorten the analysis time. Comparison of load-deformation relationship. Comparison of the change in the outer edge temperature of the laminated rubber.
статья, добавлен 10.10.2021In the article, using the self-reactance mathematical model of motion of oscillation separator with an occasion and spring pendant, on the basis of the built dependences, amplitudes of vibratory container of oscillation separator are from his kinematics.
статья, добавлен 14.09.2016Способы промышленного получения изопропилбензола. Химизм и механизм реакции алкилирования. Термодинамика и кинетика процесса. Описание программных сред, используемых для моделирования химических производств. Разработка модели ректификационной колонны.
курсовая работа, добавлен 26.10.2020The paper presents the design of experimental cells, a description of materials for construction and construction process, and preliminary results. The objective of the work is proving which of the MBT fractions function better for methane degradation.
статья, добавлен 08.10.2020