Proposal of handling process on robotized workplace with dual arm robot
Deployment of two-arm robots in different plants. Designing of an educational workplace for assembly, equipped with a two-arm robot. Using of Schunk electric grippers to adjust the range of movement and clamping force. Design a robotic workplace.
Подобные документы
Design, develop Micro Air vehicle system provides a platform to support a very wide variety of missions for the small unit. Further miniaturization of electronics and sensors these vehicles to become even smaller and to operate in complex environments.
творческая работа, добавлен 18.01.2014Построение системы автоматического управления с применением распределенных регуляторов и согласованного адаптивного управления дробильно-измельчительным комплексом горно-обогатительного комбината на базе промышленных контроллеров Schneider Electric.
статья, добавлен 30.07.2016The Safety Experience Center where you can create a space where you can experience a virtual disaster, learn how to survive, and find alternatives that can increase your viability the most. In order to commemorate the tragedy of the "Sewol ferry".
статья, добавлен 12.05.2024- 54. Simplification and verification of dynamic equations of movement of an autonomous underwater vehicle
Autonomous underwater vehicles. The dynamic equations for describing the movement of a general AUV in a fluid with nonnegligible viscous properties and the possible simplification of this equation in regard to a specific construction of a real world AUV.
статья, добавлен 27.08.2020 The model of the disperse material behavior under vibration in the hole of the dispenser based on the Navier-Stokes equations. The influence of the power factor on the movement of the product and the parameters of the hole on the vibrating dosing process.
статья, добавлен 14.09.2016Developing of a photobioreactor design for wastewater treatment in which the application of new connections reduces material consumption for the manufacture of transparent flexible tanks, reducing labor costs for installation and dismantling of tanks.
статья, добавлен 10.07.2022The need to design new drilling equipment. The analyzed existing options for solving the problem solve it to some extent. To eliminate them, it is proposed to use elastic elements (ring springs) in the construction of double-shoulder tool joints.
статья, добавлен 02.03.2021The mixed approach that combines theoretical research, analysis of scientific research with analysis of practical examples, increasing visitor engagement through augmented reality, virtual reality technologies, also encompasses important design aspects.
статья, добавлен 24.06.2024Визначення параметрів, необхідних для побудови інтегрованої схеми ХТС. Моделювання автоматизованої установки ректифікації частково розчинної азеотропної суміші в програмному середовищі UniSim Design. Створення комп’ютерної моделі інтегрованої схеми.
статья, добавлен 24.03.2016The essence of ventilation systems. Operation of special ventilation shafts, requirements for the location of the ventilation shafts. The design of the ventilation system, its role in the design of complex transport systems, road and rail tunnels.
контрольная работа, добавлен 19.02.2019A study of the collections of young Moldovan designers, graduates of the KSPU. I. Kryanga. Conceptual trends in the contemporary art of design and fashion in the country, based on the creative interpretation of artistic images by young designers.
статья, добавлен 22.05.2022The optimization procedure in computer-aided design problem. The methodic of optimal weight coefficients values choice. The use of structural models in the form of tables and morphological trees of quality variants of the signs of aerial vehicles.
статья, добавлен 14.09.2016Analysis of the evolution of approaches to the design of viable complex systems and the formation of the principles of hybrid thinking of designers on a transdisciplinary basis. Formation of the engineering design thinking as a means of adaptation.
статья, добавлен 15.09.2024Моделирование блока перегонки смеси стабильного газового конденсата в среде двух программных пакетов UniSim Design и Aspen PIMS. Принципиальная схема атмосферного блока перегонки сырья установки ЭЛОУ-АВТ-4. Основные показатели технологического режима.
реферат, добавлен 20.06.2017The historical and formation stages of the Lviv school of glassmaking are approximated. The modernization of educational mechanisms are identified, ways of their solution are suggested and applied measures that will promote implementation are outlined.
статья, добавлен 16.02.2022Computer-aided system as a solution of the computer-aided design task. Aerodynamical aspects of vertical-axis wind turbines. Principle of action of lift-driven vertical axis wind turbines. Formulation of the methodical basis for computer program.
статья, добавлен 14.09.2016The place of interdisciplinary educational technology in the system of engineering training. The role of the course of theoretical mechanics in the system of engineering disciplines. Presentation of scientific and subject knowledge of the discipline.
статья, добавлен 12.08.2020Defining of dimensional relationships where the aspect ratio. The building process for 3D microdevices. The features of creation surface energy high enough to maintain adhesion of the electroplated material until completion of the plating process.
реферат, добавлен 16.04.2017Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.20193D printing (Additive Manufacturing Process, AM) is any of various processes used to make a three-dimensional object without the use of dies, molds or machining. The most basic, differentiating principle behind 3D printing. General principle modeling.
статья, добавлен 20.02.2019The aim of the article is to consider issues related to the technological process of preserving and enriching the composition of milk. It is noted that milk, which is of great importance in nutrition due to the presence of proteins, fats, minerals.
статья, добавлен 04.10.2023Proposal and implementation of a new methodology for calculating the bending finned tubes for heat exchange systems. Getting high-quality bends with minimum radius of bending pipes bimetallic and monometallic. The use of technology in the helical rolling.
статья, добавлен 24.02.2016The purpose of the project is to create digital substations for effective management and maintenance. The use of advanced technologies, including the IEC 61850 standard and digital automation systems, will improve the monitoring, control of substations.
статья, добавлен 14.02.2025Основные задачи развития общественного питания. Необходимость укрепления материально-технической базы. Технологические требования к конструкции теплового аппарата. Описание устройства и принципа действия пароконвектомата Rational, его преимущества.
курсовая работа, добавлен 26.04.2013The two main methods of mechanical assembly of plastic parts. Requirements for reliable mechanically bonded plastic joints. Special consideration for composites. The main advantages and disadvantages of adhesive bonding (gluing or glue bonding).
статья, добавлен 10.03.2019