Modification of mechanical properties of cement mortar by adding zinc oxide nanoparticles
The flexural and compressive strength of mortar by partial replacement of cement with Nano-ZnO particles has been studied. The results showed that the flexural and compressive strength of the cement mortars with ZnO were higher than pure cement mortar.
Подобные документы
Test the tribological properties of lubricants as the main stage of assessing their suitability for use in friction. The scheme of the "cone - three ball" with the use of objects of simple geometric shapes to test different construction materials.
статья, добавлен 29.01.2016Comparison of thermal insulation properties of Sakhabult products with products of other manufacturers. Manufacturing of a dummy for monitoring the temperature difference inside sleeping bags and outerwear from natural fur of fur animals, deer and horses.
статья, добавлен 01.04.2021Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
статья, добавлен 21.12.2016Use of selective solvents in oil refining industry. Methods of cleaning oil raw materials. Technology of fractionation of extracts of phenol distillates, their chemical properties. Modeling the column of industrial extraction of petroleum products.
статья, добавлен 10.08.2018Study the structure of the coating made of composite material that contains wear-resistant components SiC-Al2O3. The use of a metallic binder based on iron in composite production. The properties of the obtained coatings with the steel counterface.
статья, добавлен 29.01.2016Знакомство с перспективами развития процесса крашения текстильных материалов. Рассмотрение основных этапов развития техники красильно-отделочного производства. Характеристика инновационного гидрофильного силиконового пластификатора Persoftal Nano-S2G.
дипломная работа, добавлен 11.10.2013Rationale for the use of advanced technology for sewage treatment schemes dairies. Removal of insoluble organic matter by adding a flotation purification scheme. Using the immersed biofilter for a disk intensive degradation of organic pollutants.
статья, добавлен 13.08.2016Evaluation of the relevance of Vernadskyi's noosphere concept. Transformation of the biosphere by man with the help of the mind. Development in the direction of the creation of technical subjects and replacement of the biosphere with the technosphere.
статья, добавлен 18.04.2023The relation between the particles velocity and the deposition efficiency of material powders. A different approaches for calculating the critical deposition velocity. Computational fluid dynamics model. Critical particle velocity determination.
статья, добавлен 29.11.2016Production polystyrene composite films with small content of fullerenes (up to 1 %) by casting o-xylene solutions. A dependence of the glass transition temperature of the composite material on its composition. The adsorption capacity of polymer material.
статья, добавлен 30.07.2016Analysis of the problem of recycling used tires. Search for methods of processing rubber waste. Investigation of foamed polymer compositions filled with rubber. The use of partial vulcanization to increase the interfacial interaction in the polymer blend.
статья, добавлен 21.12.2016Formulation of the problem of calculating the scalar potential of the electric field in the axisymmetric disk, the material which has anisotropic permittivity. The method of successive approximations, a description of the potential of the electric field.
статья, добавлен 30.08.2016The obstacle in the way of nanotechnologies is the lack of selective "scalpel and forceps", the instruments to operate with particles of size less than 10-9 meters, particularly with molecules and atoms. Atomic forceps and scalpel for nanotechnologies.
статья, добавлен 29.12.2023A modern house built using materials that "smell of the past, but strive for the future." The use of mechanical ventilation with dehumidification, radiant floor, photovoltaic panels with energy storage and heat pump. Creating a comfortable temperature.
статья, добавлен 04.10.2021Features of the two-phase model of the structure of keratin fibers. Estimation of the importance of critical and equilibrium stresses in the fibril, transfer of its stress to the matrix. Study of a possible connection between microfibrils and matrix.
статья, добавлен 30.05.2022Defining and analysis the essence of robot is an automatic device, which has a manipulator – mechanical analogue of human hand, and manipulator control system. Consideration and characteristic of the structural features model of domestic robot–helper.
статья, добавлен 29.01.2016To separate simultaneous removal of mechanical impurities and water - the main tasks of filters. Analysis of the graphical representation of the piping system for pumping fuel and necessary equipment for the storage and dispensing of fuel operations.
курсовая работа, добавлен 29.03.2018Analysis of a mathematical model to determine the transient modes of rotary kilns, drying drums and mills taking into account electromagnetic processes in the induction motor. Mechanical vibrations of the elements of the drive mechanism, long metal body.
статья, добавлен 14.09.2016Characteristics of distillation devices used in the production of alcohol in the XIX-XX centuries. Provisions of mechanical, microbiological, physicochemical, physiological theory of fermentation. The role of L. Pasteur in the study of alcohol production.
статья, добавлен 30.01.2022Dynamic designer as a way to save time and cost of getting new products to market, and improving old ones without a huge investment in equipment. Using parametric solid models for to develop the form of the parts. Mechanical desktop to build prototypes.
презентация, добавлен 21.02.2014Biodegradable poly-3-hydroxybutyrate [P(3HB)] and birch sawdust - a material for the preparation of powder mixtures for molds in the production of granules and tablets. The prospect of a composite obtained on this basis for the building industry.
статья, добавлен 17.04.2022The main stages of the automatic assembly of cylinder connection. The structural elements of the flexible automated production. Prospect for the automation of machine building production. The main types of heat exchange in technological systems.
контрольная работа, добавлен 05.04.2016Mechanical tests of with various hydrogen concentrations before and after the hydride reorientation tests were performed. Hydrogen pickup measurements in zirconium alloys: relation to oxidation kinetics. Hydride microstructure in the dummy claddings.
статья, добавлен 30.05.2021Cylinder shaped parts – one of the mostly used in printing presses. A new technology of strengthening and recovery of details based on vibration roll burnishing is offered in the article. Experimental work and scientific conclusions are described.
статья, добавлен 29.07.2016The mass variable is considered the first and most important basis for motion events. Mass is what the body contains of matter, and mass exists in three states in the universe, and it is unique. From a mechanical point of view it is considered a variable.
статья, добавлен 12.05.2024