Modeling technological support the process of grinding abrasive about
Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
Подобные документы
The roller of the belt as the most important parts of the conveyor, being subjected to continuous stress both during operation and in stopping periods. Causes and weight percentage of failures due to fatigue. Sealing system with simple labyrinth.
статья, добавлен 27.12.2016The model of spatially distributed curing process of epoxy matrix polymeric composite. The model using the projections of Pareto points set on the 8-dimensional space of design variables. Сontrol synthesis for the closed mould curing of composite spar.
статья, добавлен 30.05.2017Geometry enhancements, general beam section calculator, body diagrams and grid point force balances, graphics enhancements, scripting language and polygon and freehand selection, their application in the development of parts. Results viewing enhancements.
презентация, добавлен 21.02.2014Thermosetting plastics, their irreversible chemical reaction (polymerization), including the effects of temperature and time. Bringing the resin composition to a liquid state, forcing the liquid to flow into the cavity of the desired configuration.
статья, добавлен 10.03.2019Analysis of criteria for steels warping susceptibility under the thermochemical treatment. Study of value of the details warping during the quenching. Analysis of residual internal pressures in hardened layer and kinetics of austenitic grain growth.
статья, добавлен 30.01.2017- 106. Development of wide bandgap one-dimensional MOF/TIO2 photonic crystal and its gas-sensing properties
Metal-organic framework materials a type of coordination polymer that have seen breakthroughs in material science over the past decade. Because of their high specific surface area and porosity, they are used for gas adsorption, storage, and separation.
статья, добавлен 10.10.2024 Model for calculation of nominal stresses in characteristic points of the surface fatigue crack to the tubular shaft in bending with rotation. Reasons for the decrease of the propagation velocity of cracks in the center and changing the geometry.
статья, добавлен 28.09.2016Various experts are unanimous in the fact that technological trends in 2023 that have the potential to change the world, affect many areas of life, such as medicine, science, education and business, including in Ukraine, will be artificial intelligence.
статья, добавлен 06.11.2023Features the design of tooling for casting under pressure of zinc alloys. The problem that arise when designing a press-forms of analysis. Experiments to study thermal stability of materials, parts, equipment subject to cyclic thermo-mechanical treatment.
статья, добавлен 17.12.2016Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Defining features of the motion of moving the controls in vibroudarnogo qualifier. Analysis of the effectiveness and efficiency of processing of minerals. Creating an analytic function, which could describe the trajectory of the mass center of the rink.
статья, добавлен 24.02.2016The main production methods jet fuels rocket engines. Prospects for the use of various raw materials to produce jet fuels in the context of limited energy resources. The impact of processing production and use of aviation fuels on the environment.
статья, добавлен 23.02.2016Improving matching techniques constructional and technological parameters of the installation with the modes of its work taking into account the features of the resonator. The changes in the dielectric parameters of raw material during the heat treatment.
автореферат, добавлен 30.04.2018Consideration an alternative, in relation to the widely used "differential" one, "integrated" approach to solving the dynamics problems. Determining the natural frequencies of fluctuations case of the free surface liquid in containers of various shapes.
статья, добавлен 29.11.2016Cylinder shaped parts – one of the mostly used in printing presses. A new technology of strengthening and recovery of details based on vibration roll burnishing is offered in the article. Experimental work and scientific conclusions are described.
статья, добавлен 29.07.2016Aluminum can be considered green when its production and alloys processing are low-carbon (as well as associated with the reduced amount of other greenhouse gases, hazardous chemicals and environmental pollutants), include recycling of scrape and waste.
статья, добавлен 19.09.2024Сущность технологии и техническая характеристика 3D принтера. Основные виды и преимущества 3D-печати. Краткое описание видов печати послойного напраления (Fusing Deposition Modeling) и послойного склеивания пленок (Laminated Object Manufacturing).
контрольная работа, добавлен 18.01.2017To separate simultaneous removal of mechanical impurities and water - the main tasks of filters. Analysis of the graphical representation of the piping system for pumping fuel and necessary equipment for the storage and dispensing of fuel operations.
курсовая работа, добавлен 29.03.2018Analysis of the problem of recycling used tires. Search for methods of processing rubber waste. Investigation of foamed polymer compositions filled with rubber. The use of partial vulcanization to increase the interfacial interaction in the polymer blend.
статья, добавлен 21.12.2016The history of iron and Damascus steels through the eyes of ancient blacksmiths. Observation of color changes during heating and estimating of hardness by scratch tests, to have determined some key parts of the present-day iron-carbon phase diagram.
статья, добавлен 09.09.2012Research of the valuable properties of individual components of serum, which lead to its use during the production of food products. Purification of milk whey from milk fat by separation. Separation of colloidal and ion-molecular systems of serum.
статья, добавлен 24.06.2024Analysis of the main causes of destruction of adhesive joints. Structural and technological stress concentrators, because of which cracks develop during operation. General characteristics of the resistance of adhesive bonding to failure at all stages.
статья, добавлен 30.04.2018Technological parameters (thermal loss, cooking time, etc.) grilling the second meat dishes. Use marinades based on vegetable oil and vinegar as the most common. The composition of the marinade with yogurt and kiwi. The energy value of ready meals.
статья, добавлен 25.12.2016Studies on the preparation of pasty high-filled compositions and evaluation of their rheological properties using a rotational visco-meter "Reotest-2" on the cone-plane system. Evaluation of sedimentation resistance of compositions and their flow.
статья, добавлен 30.10.2016Test the tribological properties of lubricants as the main stage of assessing their suitability for use in friction. The scheme of the "cone - three ball" with the use of objects of simple geometric shapes to test different construction materials.
статья, добавлен 29.01.2016