Technological and chemical aspects of storage and complex processing of industrial hemp seeds
Obtaining prototypes of hemp oil by cold pressing. Determination of mass fraction of moisture оil content measurement. Indicators of seeds' quality during long storage. Yield and quality indicators of by-products obtained in the production of hemp oil.
Подобные документы
The concept and functional characteristics of diamond-like films of amorphous carbon with a high concentration of carbon with SP3. The peculiarities of their practical use. Diagram of the coating, its physical and chemical properties, the benefits.
статья, добавлен 12.06.2015Apple juices from the following four varieties of apples. Polyethylene oxide and hydrolyzed polyacrylamide. A flocculator was used to activate the flocculant through turbulence in a circular tube that was rolled into a spiral coil without a frame.
статья, добавлен 14.02.2025Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
статья, добавлен 10.03.2019Production polystyrene composite films with small content of fullerenes (up to 1 %) by casting o-xylene solutions. A dependence of the glass transition temperature of the composite material on its composition. The adsorption capacity of polymer material.
статья, добавлен 30.07.2016Characterization of features spline approximation television pictures. Rearranged algorithm spline approximation television images detailing calculation of the coefficients which gives the possibility to improve the quality of decompressing video.
статья, добавлен 26.06.2016Calculation of the coefficients autopilot unit for homing rockets based on genetic algorithms in which the autopilot block (AB) quality parameters are considered as the criterion for evaluating the optimality of the AB. Optimality of AB coefficients.
статья, добавлен 30.04.2018Structure of three-cone rock bit with inserted hard-alloyed rock-destruction and protecting equipment, in which the chief components are marked. The minimally possible set of operators, which support qualitative performance of technological process.
статья, добавлен 14.09.2016Proposal and implementation of a new methodology for calculating the bending finned tubes for heat exchange systems. Getting high-quality bends with minimum radius of bending pipes bimetallic and monometallic. The use of technology in the helical rolling.
статья, добавлен 24.02.2016Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016Various kinds of mathematical models of a snakelike robot motion depending on gait pattern. Simplified model of a snake. The motion sequence of three-mass system. The average velocity depending on number of masses. Determination of optimal masses number.
статья, добавлен 27.08.2020The aim of the article is to consider issues related to the technological process of preserving and enriching the composition of milk. It is noted that milk, which is of great importance in nutrition due to the presence of proteins, fats, minerals.
статья, добавлен 04.10.2023Study the structure of the coating made of composite material that contains wear-resistant components SiC-Al2O3. The use of a metallic binder based on iron in composite production. The properties of the obtained coatings with the steel counterface.
статья, добавлен 29.01.2016Research of new ecological and energy-saving methods of food processing. Analysis of biotechnological processing of food using enzymes of proteinases, glutamine transferases, galactosidases, enzymes of extremophilic and psychrophilic microorganisms.
статья, добавлен 15.09.2022- 114. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 Research on the identification of meat varieties and the presence of beef, sheep and goat meat in the composition of sausage products. Use of multiplex kits for real-time PCR. Cross-reactivity between sheep and goat meat given their genetic similarity.
статья, добавлен 21.03.2024Comparative analysis of the effect of chemical compounds on the process of forming an electric arc and the conditions for its combustion.Metal transfer in the interelectrode gap under experimental conditions. Specific power of electric arc discharge.
статья, добавлен 29.09.2016Information about the general state of technologies for the utilization of secondary energy resources and environmental resources. The essence of phase transitions in food production technologies. The possibility of creating energy-material circuits.
статья, добавлен 10.06.2022Description of main activities CAE Partner GmbH аn Enterprise of the MSC Group, foundation of the company and development of its in Europe. Software-products, services and the scope of production activities, which use technology developed by the company.
презентация, добавлен 21.02.2014The article is devoted to clarifying the features of stereographic images, the main aspects of using 3D printing as modern creative technology in various fields of human activity. The article analyzes the principles of creating three-dimensional products.
статья, добавлен 14.09.2020This paper discusses the changes of intestinal flora and inflammation indicators in patients with acne after receiving the honeysuckle and chrysanthemum powder intervention. In this experiment, 6 patients with acne were included in the experimental group.
статья, добавлен 14.02.2025Modernization of the transport system of the production system MPS 500. Creation of a new control program in the environment of the TIA portal. The main functions of the frequency converter. Investigation of the final state of the control cabinet.
статья, добавлен 26.08.2020Investigation of adhesive compositions based on polychloroprene for the adhesion of rubber soles to the tips of the skin. Determination of the adhesion strength of the adhesive film when stretched as the hardener content of the adhesive is increased.
статья, добавлен 21.12.2016The optimization procedure in computer-aided design problem. The methodic of optimal weight coefficients values choice. The use of structural models in the form of tables and morphological trees of quality variants of the signs of aerial vehicles.
статья, добавлен 14.09.2016Analysis of the existing methods of the automatic regulation of the process of the drying of timber. Algorithm of the regulator of kiln drier. The need of regulating the drying process taking into account the characteristics of wood and drying agent.
статья, добавлен 28.11.2016Improving the method of dynamic analysis of mechanical systems dynamic factors dynamic model which can be represented by three-mass system of row with the first driving mass with prestressing elastic drive connections. Finding the dynamic coefficients.
статья, добавлен 30.07.2016