Investigation of the stress state of a composite in the form of a layer and a half-space with a cylindrical tube at given stresses on the boundary surfaces
Solution of the problem of the theory of elasticity for a composite in the form of a half-space with a thick-walled round cylindrical tube and a layer rigidly attached to the surface of the half-space. Assessment of the stress state of the composite.
Подобные документы
Strength is assumed - index for materials which can take standard, calculated values. Significant dependence between bending resistance, absolute size of structural elements. The structure of the wood fibers - factor which determine timber quality.
статья, добавлен 25.12.2016Determination of the rolling parameters that allow obtaining a bimetallic ribbed bar. Familiarization with the shape and dimensions of the round ribbed finished pass and of the bimetallic flat oval band obtained in numerical modelling - cross-section.
доклад, добавлен 24.12.2014The main factors of physical phenomena that accompany the process of power explosive effect for the development of new processes of metal processing. Industrial testing of facing technology by explosion of artificial surfaces of complex configuration.
статья, добавлен 19.02.2019Square Lead-Rubber Bearings with four lead plugs to round Lead-Rubber Bearings with one lead plugs and shorten the analysis time. Comparison of load-deformation relationship. Comparison of the change in the outer edge temperature of the laminated rubber.
статья, добавлен 10.10.2021The concept and functional characteristics of diamond-like films of amorphous carbon with a high concentration of carbon with SP3. The peculiarities of their practical use. Diagram of the coating, its physical and chemical properties, the benefits.
статья, добавлен 12.06.2015- 106. Development of wide bandgap one-dimensional MOF/TIO2 photonic crystal and its gas-sensing properties
Metal-organic framework materials a type of coordination polymer that have seen breakthroughs in material science over the past decade. Because of their high specific surface area and porosity, they are used for gas adsorption, storage, and separation.
статья, добавлен 10.10.2024 Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
статья, добавлен 10.03.2019The regularities of macromolecules behavior in the flow with longitudinal velocity gradient and manifested in this case effects of elastic deformations have importance in understanding the mechanism of anomalously high cutting power of water-polymer jet.
статья, добавлен 28.02.2016The historical and formation stages of the Lviv school of glassmaking are approximated. The modernization of educational mechanisms are identified, ways of their solution are suggested and applied measures that will promote implementation are outlined.
статья, добавлен 16.02.2022Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019Character of force of friction is investigated and set in nominally-immobile connections on the stage of nominal adhesion and to passing to skidding. The capacity of connections are given by the method of coating on the basis of fusible to the alloy.
статья, добавлен 27.07.2021Consideration an alternative, in relation to the widely used "differential" one, "integrated" approach to solving the dynamics problems. Determining the natural frequencies of fluctuations case of the free surface liquid in containers of various shapes.
статья, добавлен 29.11.2016Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016Directions of development of production technology of high-precision parts. Research in the field of management precision and quality parameters of the treated surface. Improvement of the technological process, equipment, instruments and devices.
статья, добавлен 06.12.2016Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Geometry, FE analys, optimization, mechanisms, plastics and MSC/ARIES positioning for design detail. Full function ACIS based modeler, constraints, region operator to sub-divide geometry. Pre release solids shelling, per face (uniform) thickness control.
презентация, добавлен 21.02.2014Comparison of the results of processing arrays light absorption alternate method of incorporating calibration surface with other methods. Determination of Ni2 +, Co3 +, Fe2 +, Cu2 + from 1-(2-pyridylazo)-2-naphthol in aqueous-micellar environment.
статья, добавлен 23.02.2016Studies on the preparation of pasty high-filled compositions and evaluation of their rheological properties using a rotational visco-meter "Reotest-2" on the cone-plane system. Evaluation of sedimentation resistance of compositions and their flow.
статья, добавлен 30.10.2016Increase in the use of hard, high strength and temperature resistant materials in engineering necessitated the development of machining techniques. Abrasive flow machining as process non-conventional machining processes. Magneto abrasive flow machining.
статья, добавлен 02.06.2014The methods of defrosting frozen berries affect sensory characteristics and the indicator of cell juice loss of the resulting product. This method preserved the tissue strength of the berry surface completely, resulting in null loss of cell juice.
статья, добавлен 14.02.2025In the article, using the self-reactance mathematical model of motion of oscillation separator with an occasion and spring pendant, on the basis of the built dependences, amplitudes of vibratory container of oscillation separator are from his kinematics.
статья, добавлен 14.09.2016The essence of a comprehensive study of the operational characteristics and reliability of roller bearings. Analysis of a mathematical model to express rolling pad durability as a function of a random argument based on the conductivity distribution law.
статья, добавлен 12.08.2022Fast fatigue crack growth. The general content of nitrogen in the alloy system that limits fatigue life. Fragmenting the titanium sponge into small pieces and using various melting methods metals. Investigation of the Partially Melted Electrodes.
статья, добавлен 10.12.2018- 124. Finding the conditions of hydrocarbons safe storing and transportation in tanks of different shapes
Application of the software package ConvEx in the design of storage tanks for petroleum products prone to self-degradation. Investigation of the influence of the geometric shape of the vessel on the critical temperature of storage of petroleum products.
статья, добавлен 10.05.2018 Investigation of multilayer coatings with different bilayer periods 8-100 nm. Using of very thin layers in multilayered system leads to increasing of specific density of interphase boundaries and it leads to increasing of critical loading of destruction.
статья, добавлен 30.07.2016