The study of the cutting force and its components in radial-circular cutting of the gears
Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
Подобные документы
Methods of the equation of the cutting edge in the absolute coordinate system. A helix - a trace of movement of the cutting tool along the workpiece. Characteristics of the mathematical model of the formation of the microrelief surface when grinding.
??????, добавлен 06.05.2018Types of tool materials: from high-carbon steel to ceramics and diamonds, and their use as cutting tools in the modern metal industry. Cutting tool and its characteristics: hardness, strength. Achieving an acceptable tool life before replacing it.
??????, добавлен 26.04.2019???????? ????????????? ?????????? ????????????????? ??????? High Speed Cutting. ??????? ?????????? HSC. ?????? ??????? ??? ???????????? ? ???????????????? ?????????. ?????? ? ????????? ??????? ????????????. ???????? ????????, ??????? ??????????.
??????, добавлен 30.01.2018Appointment, device and action of the turning machine. Types of lathes, depending on the application. Metal processing on machine tools, turning operations. The use of water energy to drive. The principle of operation of the hydroelectric station.
??????, добавлен 11.03.2019The adapted pitch concept involves varying the pitch and the length of the cutting portion as a function of the taper of the instruments. HEROShapers used to prepare and enlarge the coronal and middle thirds of the canal. The removal of dentinal chips.
??????, добавлен 10.12.2013Service robot - device which used for cutting the grass or vacuum cleaning. Repairing of damaged inner pipe wall. Substituted human in dangerous or monotonous works via using of robots. Cleaning brush module for dirties removing. Design of tracked robot.
??????, добавлен 28.08.2020Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
??????, добавлен 14.09.2016Apple juices from the following four varieties of apples. Polyethylene oxide and hydrolyzed polyacrylamide. A flocculator was used to activate the flocculant through turbulence in a circular tube that was rolled into a spiral coil without a frame.
??????, добавлен 14.02.2025Analyzed the impact of long-term operation of gas pipelines, as well as natural stress concentrators on the physico-mechanical properties of welded joints of steel 17G1S. Regularities of the destruction of the material of welded joints of gas pipelines.
??????, добавлен 30.01.2016Nonaxisymmetric boundary value problem of elasticity theory for multiconnected body with cylindrical boundaries. Boundary conditions by the generalized Fourier method. The numerical analysis of stresses in the areas of their greatest concentration.
??????, добавлен 30.10.2016Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
??????, добавлен 14.09.2016Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
??????, добавлен 10.03.2019The configuration of an anorectal pressure gauge probe, the study of the location of sensors, the radial array of anal sensors, the location and length of the balloon, the pressure sensor inside the balloon. List of tests based on potential indication.
??????, добавлен 29.03.2020Modeling and principle of operation positioner power consumption in the direct mode of automated management. Evaluation of the use of the corrected function decline in electricity consumption in the automated control system of technological process.
??????, добавлен 28.02.2016The study of structural changes during hot deformation metal during controlled rolling. The influence of preheating temperature and deformation degree on the size and shape of austenite grains. The definition of the polygonal structure of the austenite.
??????, добавлен 30.01.2017- 16. The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
??????, добавлен 29.01.2016 The methodical approach that is aimed at the efficient use of existing fixed assets and technological innovations introduction. Technical and technological components of the technological machine-building enterprise "Turbomash Ltd" development.
??????, добавлен 26.08.2016Deployment of two-arm robots in different plants. Designing of an educational workplace for assembly, equipped with a two-arm robot. Using of Schunk electric grippers to adjust the range of movement and clamping force. Design a robotic workplace.
??????, добавлен 28.08.2020The bread was made from type 500 wheat flour with the addition of pumpkin seed, chestnut or rosehip flour Bread staling was determined by measuring the deformation characteristics of the bread crumb. The total, plastic, elastic deformation of the bread.
??????, добавлен 14.02.2025Consideration the mathematical model of process of pressing of seamless pipes. Effect on various forms of rolling shaping matrix. The nature of the formation of the deformation zone. Development of direct compression on a cylindrical mandrel pipe.
??????, добавлен 30.01.2016A method of determining the effective longitudinal elastic modulus for the composite material in the problem of longitudinal tensile composite. Unidirectional composite material with a hexagonal arrangement of fibers. The effective elastic modulus.
??????, добавлен 27.09.2016The study investigates the kinematics of robots with the aim of expedient use of certain engineering solutions solving certain problems related to the accuracy of robot movement. The object of study is various types of robots and their kinematic systems.
??????, добавлен 20.07.2024System for billet continuous caster’s mould heat engineering parameters monitoring. Formation of the internal heat transfer surfaces. Calculation the indicators: average heat flux density, overall heat exchange coefficient. Effective gas gap thickness.
??????, добавлен 30.01.2016Characterization of elastic properties of saturated hydrocarbons and associates resinous-asfaltenovyh of compounds by simulating molecular dynamics. Evaluation of rheological behavior of heavy oil the elasticity matrix of transversely isotropic material.
??????, добавлен 27.07.2016The main advantages and disadvantages of well-known spiral drills with a multi-stage blade. It is described that the bridge, together with the steps adjacent to the grooves, is a small centering drill, performs centering and drilling during the process.
??????, добавлен 10.02.2021