Billet continuous caster’s moulds heat engineering parameters monitoring system
System for billet continuous caster’s mould heat engineering parameters monitoring. Formation of the internal heat transfer surfaces. Calculation the indicators: average heat flux density, overall heat exchange coefficient. Effective gas gap thickness.
Подобные документы
Исследование алгоритма усреднения параметров орбиты Международной космической станции, примененный при реализации совместного с европейским космическим агентством космического эксперимента Global Time System 2. Поведение ошибок по долготе и по широте.
статья, добавлен 28.10.2018Transit of natural gas along the territory of Ukraine to the countries of the Western and Central Europe. Main resons of the loss of pipeline efficiency. Necessity for studying of the operation modes of the gas transport system during underloading.
статья, добавлен 01.12.2017The article discusses one of the promising directions of development of the electric power industry, associated with the use of controlled AC power lines using FACTS devices, in particular, the advantages of static thyristor compensators are considered.
статья, добавлен 10.12.2024Obtaining prototypes of hemp oil by cold pressing. Determination of mass fraction of moisture оil content measurement. Indicators of seeds' quality during long storage. Yield and quality indicators of by-products obtained in the production of hemp oil.
статья, добавлен 24.06.2022Design, develop Micro Air vehicle system provides a platform to support a very wide variety of missions for the small unit. Further miniaturization of electronics and sensors these vehicles to become even smaller and to operate in complex environments.
творческая работа, добавлен 18.01.2014Controlling the rudder, counting the distance traveled, turning off the engine and resetting the wings - the simplest autopilot functions. Radio control - the technology, that allows drones to follow difficult routes, perform maneuvers in the air.
статья, добавлен 27.02.2021Motion systems as core technologies, as mechanical systems, like microelectronic manufacturing equipment, are required to achieve high speed and accuracy. The influence of the dynamics of a mechanical system on the quality of the position tracking syste
статья, добавлен 26.08.2020The traditional irrigation method, based on simple open canal systems, is extremely ineffective for managing critical and limited water resources. Conduct a qualitative assessment of irrigation water losses due to evaporation and system inefficiencies.
статья, добавлен 03.10.2021Defining and analysis the essence of robot is an automatic device, which has a manipulator – mechanical analogue of human hand, and manipulator control system. Consideration and characteristic of the structural features model of domestic robot–helper.
статья, добавлен 29.01.2016Hydrothermal sol-gel synthesis of hexagonally ordered silicas using a hybrid template system is reported. Silicas were characterized by IR spectroscopy, X-ray diffraction techniques as well as electron microscopy. The hexagonal structure of MCM-41.
статья, добавлен 30.07.2016To separate simultaneous removal of mechanical impurities and water - the main tasks of filters. Analysis of the graphical representation of the piping system for pumping fuel and necessary equipment for the storage and dispensing of fuel operations.
курсовая работа, добавлен 29.03.2018The model of spatially distributed curing process of epoxy matrix polymeric composite. The model using the projections of Pareto points set on the 8-dimensional space of design variables. Сontrol synthesis for the closed mould curing of composite spar.
статья, добавлен 30.05.2017The recent work on Micro Aerial Vehicles (MAV) at the Institute of Aerospace Systems. Basics of MAV Research. Flightmechanical simulation. Wind tunnel tests. Overall controller system structure. The inertial measurement unit. On-Board computer structure.
творческая работа, добавлен 18.01.2014Fast fatigue crack growth. The general content of nitrogen in the alloy system that limits fatigue life. Fragmenting the titanium sponge into small pieces and using various melting methods metals. Investigation of the Partially Melted Electrodes.
статья, добавлен 10.12.2018Use of fluid with magnetorheological effect in crane’s system can reduce significantly unwanted overload, vibrations and resonances arising from them. Applying periodically changing strengths of an external synchronized with cycles of periodical crane's.
статья, добавлен 28.11.2016The problem of fuzzy multicriterial analysis of local energy conversion systems. Construction of training samples for artificial neural networks. Application of multiagent calculating models. Transition from vectorial criterion to a scalar combination.
статья, добавлен 28.08.2016Estimation of energy release in mills of various types to understand the thermodynamic aspect of processes during mechanoactivation treatment. Modeling the motion of the balls of a mill and evaluating the generation of energy in the ball system.
статья, добавлен 07.08.2020Improving the method of dynamic analysis of mechanical systems dynamic factors dynamic model which can be represented by three-mass system of row with the first driving mass with prestressing elastic drive connections. Finding the dynamic coefficients.
статья, добавлен 30.07.2016Modeling and principle of operation positioner power consumption in the direct mode of automated management. Evaluation of the use of the corrected function decline in electricity consumption in the automated control system of technological process.
статья, добавлен 28.02.2016Studies on the preparation of pasty high-filled compositions and evaluation of their rheological properties using a rotational visco-meter "Reotest-2" on the cone-plane system. Evaluation of sedimentation resistance of compositions and their flow.
статья, добавлен 30.10.2016A divider for planar antennas is considered. Diffraction problems for junctions of planar waveguides with infinitely thin walls and for walls with finite thickness are considered in the article. Some important for design numerical results are presented.
статья, добавлен 04.11.2018Determination the rigidity of constructive elements involved into the rated diagram of electromechanical system of the drive of spherical mill. Defining the rigidity of the elements entering a kinematic circuit of any electromechanical systems of drives.
статья, добавлен 28.11.2016Geometry, FE analys, optimization, mechanisms, plastics and MSC/ARIES positioning for design detail. Full function ACIS based modeler, constraints, region operator to sub-divide geometry. Pre release solids shelling, per face (uniform) thickness control.
презентация, добавлен 21.02.2014Возможности получения керамики на основе диоксида циркония современными перспективными методами. Прессование с мощным ультразвуковым воздействием с последующим спеканием и искровым плазменным спеканием. Зависимость свойств изделий от режимов синтеза.
дипломная работа, добавлен 17.05.2017Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019