Investigation of restoration dimensional parameters rods pump gas transport process by electric-spark alloying
Investigation of the surface layer structure at high resolution. Study of surface morphology of treated detail. The use of electric-surface alloying components operating under conditions of friction and abrasionerosion wear and their restoration.
Подобные документы
Deployment of two-arm robots in different plants. Designing of an educational workplace for assembly, equipped with a two-arm robot. Using of Schunk electric grippers to adjust the range of movement and clamping force. Design a robotic workplace.
статья, добавлен 28.08.2020Studies on the preparation of pasty high-filled compositions and evaluation of their rheological properties using a rotational visco-meter "Reotest-2" on the cone-plane system. Evaluation of sedimentation resistance of compositions and their flow.
статья, добавлен 30.10.2016Increase in the use of hard, high strength and temperature resistant materials in engineering necessitated the development of machining techniques. Abrasive flow machining as process non-conventional machining processes. Magneto abrasive flow machining.
статья, добавлен 02.06.2014Formulation of the problem of calculating the scalar potential of the electric field in the axisymmetric disk, the material which has anisotropic permittivity. The method of successive approximations, a description of the potential of the electric field.
статья, добавлен 30.08.2016The study of methods of improving mechanical properties of coatings of implants by reducing the value of young's modulus and coefficient of friction in the fluids of the body to improve the tribological parameters of the implants with ceramic coatings.
статья, добавлен 29.01.2016Study the structure of the coating made of composite material that contains wear-resistant components SiC-Al2O3. The use of a metallic binder based on iron in composite production. The properties of the obtained coatings with the steel counterface.
статья, добавлен 29.01.2016The conductive nanocomposite films on the basis of reactionary copolymers received. The threshold of their percolation is determined. It was shown that its value depends on the size of specific surface of nanotubes and conditions of composite obtaining.
статья, добавлен 23.09.2016The electric drive of Crane mechanisms. The powered motor speed control via frequency converter and process control via programmable logic controller. Cranes are an important part of many industries and construction sites used for lifting heavy loads.
статья, добавлен 14.02.2025Comparison of the results of processing arrays light absorption alternate method of incorporating calibration surface with other methods. Determination of Ni2 +, Co3 +, Fe2 +, Cu2 + from 1-(2-pyridylazo)-2-naphthol in aqueous-micellar environment.
статья, добавлен 23.02.2016Общая характеристика линейки паровых турбин для парогазовых установок от предприятия General Electric Power Systems, предназначенных для работе на паре, получаемом в одном или нескольких котлах-утилизаторах за счет теплоты отработавших газов ГТУ.
статья, добавлен 28.05.2018Analysis of design features and parameters of automobile and aircraft engines is carried out. It is shown that car engines, despite the high technical level achieved at the beginning of the 21st century, do not technically meet aviation requirements.
статья, добавлен 19.06.2022Analysis of the development of the basic methods of engineering the contact surfaces of tribological systems. Characteristics of the problems and prospects of development of technologies of creating surfaces of discrete-oriented structure of the system.
статья, добавлен 18.02.2016Scientific justification for automated control method of optimal charge of pebble mill operating in series with a magnetic separator in the second stage of crushing in magnetic separating plants that process on iron ores with varying physical properties.
статья, добавлен 23.03.2016The mechanisms used in industrial enterprises, crane mechanisms are one of the most common. This overhead cranes, which are the main types of crane mechanisms. For the optimal choice of electric drive, the basic requirements were taken into account
статья, добавлен 14.02.2025Modernization of the transport system of the production system MPS 500. Creation of a new control program in the environment of the TIA portal. The main functions of the frequency converter. Investigation of the final state of the control cabinet.
статья, добавлен 26.08.2020The production of electricity, losses during its distribution are considered as an important issue. Currently, loss control and electricity metering. Electricity measurement, detection and elimination of losses affect energy-saving technologies.
статья, добавлен 14.02.2025Polytetrafluoroethylene as one of the promising polymers for tribotechnical purposes. The use of polysulfonamide fiber to increase the wear resistance of polytetrafluoroethylene under conditions of friction without lubrication in reciprocating motion.
статья, добавлен 11.08.2021Research of influence of the electric discharge machining on change the properties of water. The formation of free radicals and hydrogen peroxide under the influence of cavitation is established, which leads to an increase in the whiteness of the wool.
статья, добавлен 21.12.2016Model for calculation of nominal stresses in characteristic points of the surface fatigue crack to the tubular shaft in bending with rotation. Reasons for the decrease of the propagation velocity of cracks in the center and changing the geometry.
статья, добавлен 28.09.2016Построение системы автоматического управления с применением распределенных регуляторов и согласованного адаптивного управления дробильно-измельчительным комплексом горно-обогатительного комбината на базе промышленных контроллеров Schneider Electric.
статья, добавлен 30.07.2016Study of structure and properties of aluminum alloys treated with nanodispersed modifiers. Consideration of the classical theory of modification of melts. Creation of fine-grained structure of castings. Analysis of existing aluminum alloy modifiers.
статья, добавлен 21.04.2020Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019Consideration an alternative, in relation to the widely used "differential" one, "integrated" approach to solving the dynamics problems. Determining the natural frequencies of fluctuations case of the free surface liquid in containers of various shapes.
статья, добавлен 29.11.2016Analysis of criteria for steels warping susceptibility under the thermochemical treatment. Study of value of the details warping during the quenching. Analysis of residual internal pressures in hardened layer and kinetics of austenitic grain growth.
статья, добавлен 30.01.2017Improving the physical and mechanical properties of powder steels. Study of the effect of heat treatment on the structure of powder carbon steels with carbon-containing components. Research of heat treatment processes: hardening, tempering and annealing.
статья, добавлен 27.02.2021