About some specific motions of movable operating elements in the vibroimpact roll classifier
Investigation of the mechanism of movement of working bodies vibroimpact classifier for the purpose of improving the efficiency and performance of mineral processing. Qualitative and quantitative analysis of the dynamics of working bodies of the pendulum.
Подобные документы
Development of a diagram and installation of a prototype of a two-flow heat pipe with the ability to regulate the parameters of the working environment. Using of the method of pulsed supply of liquid coolant to increase the heat transfer of a heat pipe.
статья, добавлен 14.12.2024The use of the boundary values of parameters of mould displacement of the earth's surface and refining the workings of the design scheme to predict the trajectory of sedimentation. Determination of empirical coefficients of mathematical equations.
статья, добавлен 30.07.2016Rational modes of printing volumetric samples with a working thickness of the 316L powder layer of 40 μm to achieve a density of volumetric samples/ Determination of the density of metal samples by the metallographic method on an optical microscope.
статья, добавлен 19.03.2024Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Creation and testing of a model of a diesel engine muffler. Plotting a pressure level diagram inside the device. Analysis of the distribution of the sound field. Assessment energy losses of exhaust gases. Estimation of the spectrum and octave bandwidth.
статья, добавлен 10.10.2024Analysis of requirements for electric-drive of mechanism of pulsed wire feed, and the benefits of using a special Brushless Direct Current electric-drive. Design of half-bridge circuit to regulate the strength of the current phase of the stator windings.
статья, добавлен 22.12.2016In the article, using the self-reactance mathematical model of motion of oscillation separator with an occasion and spring pendant, on the basis of the built dependences, amplitudes of vibratory container of oscillation separator are from his kinematics.
статья, добавлен 14.09.2016Consideration and characteristics of the scheme double-point wheel-rail interaction. Familiarization with the erosive wearing. Definition of the dependence of the coefficient of adhesion on the temperature. Analysis of sand system of the locomotive.
статья, добавлен 26.09.2016Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016Determination of torque on the shaft of auger intensifier, power consumption, energy intensity and productivity of the backfilling workflow. Evaluation of soil properties, geometric parameters of the screw intensifier and speed of the bulldozer.
статья, добавлен 01.12.2017The relation between the particles velocity and the deposition efficiency of material powders. A different approaches for calculating the critical deposition velocity. Computational fluid dynamics model. Critical particle velocity determination.
статья, добавлен 29.11.2016Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
статья, добавлен 14.09.2016In the test of diesel engine, because the performance test of multi cylinder engine with different configuration needs to be replaced, and there is a certain risk in the first test, while the single cylinder engine is more suitable for the research.
статья, добавлен 03.09.2024Integration of the R.I. 01 industrial robot into the working system of the BB-01 flexible line. Operational and design features of the R.I. 01 loading robot. The central spindle of the system. The horizontal frame holding the arm of the loading robot.
статья, добавлен 25.10.2010The need to design new drilling equipment. The analyzed existing options for solving the problem solve it to some extent. To eliminate them, it is proposed to use elastic elements (ring springs) in the construction of double-shoulder tool joints.
статья, добавлен 02.03.2021Determination the rigidity of constructive elements involved into the rated diagram of electromechanical system of the drive of spherical mill. Defining the rigidity of the elements entering a kinematic circuit of any electromechanical systems of drives.
статья, добавлен 28.11.2016Investigation of multilayer coatings with different bilayer periods 8-100 nm. Using of very thin layers in multilayered system leads to increasing of specific density of interphase boundaries and it leads to increasing of critical loading of destruction.
статья, добавлен 30.07.2016Types of the combined mechanisms of simultaneous turning and folding blades, which can be stabilized the frequency of rotation of horizontal-axis wind turbines. Analysis of the dependence of the adjusting movement of the slide from rotation angles.
статья, добавлен 27.10.2016Characteristics of mathematical model of dynamic processes that occur in frictional hardening of flat surfaces of machine parts with use of the tool with the cut transverse grooves on its working parts. Cyclic circuit of the machine’s oscillations.
статья, добавлен 14.09.2016Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019Analysis of design features and parameters of automobile and aircraft engines is carried out. It is shown that car engines, despite the high technical level achieved at the beginning of the 21st century, do not technically meet aviation requirements.
статья, добавлен 19.06.2022The main production methods jet fuels rocket engines. Prospects for the use of various raw materials to produce jet fuels in the context of limited energy resources. The impact of processing production and use of aviation fuels on the environment.
статья, добавлен 23.02.2016The basic connotation of electrical engineering and automation and intelligent technology, analyzes the electrical engineering and automation intelligent technology application in improving the level of system control, improve data processing accuracy.
статья, добавлен 24.02.2025Analysis of the aspects of the specifications and drawings of plastics that are specific to this family of materials and processes and that are related to the realities that need to be taken into account. Cavity identification and rough indication.
статья, добавлен 10.03.2019