Early Assessment of Health Technologies
Analysis of ideas about conducting an early assessment of emerging medical technologies. Developing medical products and services with added value. Determining the commercial viability of medical products and services in the early stages of development.
Подобные документы
Obtaining complex fertilizers by oxidation of Angren brown coal with a mixture of nitric and sulfuric acids and decomposition of oxidation products with a mineralized mass and slime phosphorite of the Central Kyzyl Kum. Fertilizers' commercial properties.
статья, добавлен 27.01.2021There exists a wide range and a considerable potential of alternative gas fuel types. Uncertainty, flexibility of nonconventional fuels’ composition seriously limits the possible exploitation of these energy sources. Equations of chemical thermodynamics.
статья, добавлен 30.07.2016The manufacturing industry may be a key sector for the application of this technology, reduce the use of conventional energy sources, especially in the food industry located in the Andean region. Ecuadorian policies and regulations on renewable energy.
статья, добавлен 23.07.2021The mixed approach that combines theoretical research, analysis of scientific research with analysis of practical examples, increasing visitor engagement through augmented reality, virtual reality technologies, also encompasses important design aspects.
статья, добавлен 24.06.2024Creation and testing of a model of a diesel engine muffler. Plotting a pressure level diagram inside the device. Analysis of the distribution of the sound field. Assessment energy losses of exhaust gases. Estimation of the spectrum and octave bandwidth.
статья, добавлен 10.10.2024Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019The purpose of research was isolation and identification of Enterococcus species from raw milk and traditional dairy products and their biochemical properties were examined. Some biochemical and technological properties of the strains were determined.
статья, добавлен 28.05.2022The state of the tractor plant in Changchun, assessment of its impact on the surrounding area. A brief historical analysis of the development of the plant, transformation of the land belonging to it. Ways to replace spoiled land in an industrial area.
статья, добавлен 01.09.2021The development of scientific and methodological bases of forming of structural and phase composition of alloys synthesized by the combined processes which consist of the metallothermic stage and SHS (self-propagating high-temperature synthesis).
статья, добавлен 07.09.2022This work is devoted to the decision of scientific and technical problems of the day, namely to the development of scientific and methodological bases of forming of structural and phase composition of alloys synthesized by the combined processes
статья, добавлен 20.09.2022Comprehensive analysis of allelic protein variants suitable for use in bakery products made from Iraqi wheat varieties, as well as biological evaluation of these varieties using a genetic source using a general method of qualitative grain selection.
статья, добавлен 18.03.2021An overview of the current trend in the development, production and application of efficient biodegradable polymer materials and composites. Ways of hybrid modification of biodegradable polymeric composite for obtaining effective products based on them.
статья, добавлен 24.09.2023Development of a managed system architecture with the possibility of full-scale parametric optimization. Systematization of the architecture of the conversion system by the example of the technological process of liquid heating. Software designer EFFLI.
статья, добавлен 30.10.2016Approaches to optimization and the development of the model given the parameters and constraints of the subject area to improve the efficiency of product quality. Modules of adaptation and realization of adaptation functions and testing system components.
статья, добавлен 30.07.2016Research of new ecological and energy-saving methods of food processing. Analysis of biotechnological processing of food using enzymes of proteinases, glutamine transferases, galactosidases, enzymes of extremophilic and psychrophilic microorganisms.
статья, добавлен 15.09.2022The present study is a mathematical modeling aimed at the dynamic force analysis of printed circuit boards in order to eliminate dynamic stresses to an acceptable level and ensure the strength and reliability of the printed circuit board design.
статья, добавлен 02.06.2022Impact indicators coal shiites in the properties of the resulting coke. Coking process with the help of passive experiment. Effect of changes in the number of components of the coal charge on the quality of the coke at various technologies of sintering.
статья, добавлен 29.07.2016Properties and structure of hydrocarbons. Types and communication aromatics. The nature of the relationship between the carbon atoms. The methods of extraction and processing of oil. The use of the rectification columns for fractionating of raw materials.
презентация, добавлен 30.06.2014The service designed to facilitate the process of SCs, with demonstrating its elements in particular, database and knowledge base, arrangement of information for various users. In the authors’ opinion, such services will become a step towards no sphere.
статья, добавлен 13.10.2022Research of mathematical model of the process intrusion forming polymer products. Establishing a dependency on the angle of melt costs lifting screw injection unit in the material cylinder based on the geometric parameters of extrusion head and mold.
статья, добавлен 18.02.2016Dynamic designer as a way to save time and cost of getting new products to market, and improving old ones without a huge investment in equipment. Using parametric solid models for to develop the form of the parts. Mechanical desktop to build prototypes.
презентация, добавлен 21.02.2014Familiarity with the basic method of identification of defects of the drive with induction motor using wavelet transform for the test signals. Analysis of a neural network model converted to the next subsequent stages on the basis of the algorithm.
статья, добавлен 28.08.2016The methodical approach that is aimed at the efficient use of existing fixed assets and technological innovations introduction. Technical and technological components of the technological machine-building enterprise "Turbomash Ltd" development.
статья, добавлен 26.08.2016Cream with a fat content of 10%, as well as creams with the addition of whey protein, hydrolysed whey concentrates, and glucose-fructose syrup served as objects of study. Study the influence of the presence of protein and carbohydrate ingredients.
статья, добавлен 14.02.2025