Effects of fuel rod cladding temperature and stressed conditions on hydride reorientation
Mechanical tests of with various hydrogen concentrations before and after the hydride reorientation tests were performed. Hydrogen pickup measurements in zirconium alloys: relation to oxidation kinetics. Hydride microstructure in the dummy claddings.
Подобные документы
Review of the principles of operation and features of plasma-pulse impact on the oil reservoir. Analysis of the results of studies conducted under various conditions. Examples of successful implementation of this technology in oil production practice.
статья, добавлен 12.12.2024Polytetrafluoroethylene as one of the promising polymers for tribotechnical purposes. The use of polysulfonamide fiber to increase the wear resistance of polytetrafluoroethylene under conditions of friction without lubrication in reciprocating motion.
статья, добавлен 11.08.2021Consideration of the laws dynamics and growth of vapor bubbles and crystals in the solution. Study of dynamic behavior of a three-phase, two-component medium in an axially symmetric channel. Analysis of the conditions necessary for the crystallization.
статья, добавлен 24.02.2016Tissue Paper and its properties. Space and weight characteristics. Carrier and type of aircraft for transportation. Limitations by sizes, weight and loading on the floor. Calculation of number of bags that we can put into one box. Manipulation signs.
курсовая работа, добавлен 16.12.2013Analysis of design features and parameters of automobile and aircraft engines is carried out. It is shown that car engines, despite the high technical level achieved at the beginning of the 21st century, do not technically meet aviation requirements.
статья, добавлен 19.06.2022Character of force of friction is investigated and set in nominally-immobile connections on the stage of nominal adhesion and to passing to skidding. The capacity of connections are given by the method of coating on the basis of fusible to the alloy.
статья, добавлен 27.07.2021Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016- 108. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 Study of problems the sufficient conditions for the existence of solutions of linear nonhomogeneous impulsive boundary value problems with small perturbations when generating boundary value problem of impulsive has solutions for arbitrary right-hand side.
статья, добавлен 30.01.2017The system of rest is energy-saving, with power supply from alternative energy sources intended for complex recovery of an organism in house conditions. Determine the effectiveness of panel modules on the level of stress. Application panel "Ananta 2016".
статья, добавлен 19.12.2017Experimental researches of improvement of technology of preparation of preparation Torasemide 5 mg / ml a solution for injections, a choice of a filtering material. Aseptic production conditions using sterile filtration and thermal sterilization.
статья, добавлен 01.12.2017Gathering of materials about a petroleum industry in a museum creates favorable conditions for their protection. The assemblage of materials is stored In a museum about the factory "Brothers Nobel". The oil extracted by brothers Nobel in 1894-1903.
статья, добавлен 03.03.2018Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
статья, добавлен 21.12.2016Investigation of the surface layer structure at high resolution. Study of surface morphology of treated detail. The use of electric-surface alloying components operating under conditions of friction and abrasionerosion wear and their restoration.
статья, добавлен 22.03.2016Economic and social challenges of breakthrough technologies in the context of Industry 4.0, Industry 5.0, their impact on sustainable development. Technologies for creating the Internet of Things. Potential characteristics of disruptive technologies.
статья, добавлен 30.11.2020Problems of hardware configuration in systems for stabilization of information and measuring devices operated at vehicles of wide class in difficult conditions of disturbances action. Analysis of modern devices and units used in stabilization systems.
статья, добавлен 14.09.2016The conductive nanocomposite films based on functional reactive copolymers and bifunctional alcohols. Creation multiwall carbon nanotubes. Dependence properties of the nanocomposites from the specific composite composition and obtaining conditions.
статья, добавлен 30.07.2016Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016Study of field distribution in structures such as a gold lattice, a graphene layer, and a silicon substrate. Conditions of maximum electromagnetic field distribution by these structures for the purpose of using them in photonics and electronics devices.
статья, добавлен 24.02.2024