Influence of starch products on the vitality and activity of lactic acid bacteria in yogurt
Products of enzymatic hydrolysis of corn starch are promising multifunctional ingredients in yogurt, but their use requires studying influence on the vitality and activity of lactic acid bacteria, as well on some chemical characteristics of the product.
Подобные документы
Aniline and its polymerization on cotton fabric to produce conductive cotton by chemical polymerization. Polyaniline is one of the electrically conductive polymers. Polymerization using several concentrations of aniline (ANI) and hydrochloric acid.
статья, добавлен 15.01.2021During the development of natural resources of people actively in contact with unfavorable environmental conditions. It concerns the use of floating means. To reduce the adverse effects of environment requires the design of products for special purposes.
статья, добавлен 25.11.2016Technological parameters (thermal loss, cooking time, etc.) grilling the second meat dishes. Use marinades based on vegetable oil and vinegar as the most common. The composition of the marinade with yogurt and kiwi. The energy value of ready meals.
статья, добавлен 25.12.2016There exists a wide range and a considerable potential of alternative gas fuel types. Uncertainty, flexibility of nonconventional fuels’ composition seriously limits the possible exploitation of these energy sources. Equations of chemical thermodynamics.
статья, добавлен 30.07.2016Obtaining prototypes of hemp oil by cold pressing. Determination of mass fraction of moisture оil content measurement. Indicators of seeds' quality during long storage. Yield and quality indicators of by-products obtained in the production of hemp oil.
статья, добавлен 24.06.2022Polytetrafluoroethylene as one of the promising polymers for tribotechnical purposes. The use of polysulfonamide fiber to increase the wear resistance of polytetrafluoroethylene under conditions of friction without lubrication in reciprocating motion.
статья, добавлен 11.08.2021The purpose of research was isolation and identification of Enterococcus species from raw milk and traditional dairy products and their biochemical properties were examined. Some biochemical and technological properties of the strains were determined.
статья, добавлен 28.05.2022Transit of natural gas along the territory of Ukraine to the countries of the Western and Central Europe. Main resons of the loss of pipeline efficiency. Necessity for studying of the operation modes of the gas transport system during underloading.
статья, добавлен 01.12.2017Consideration the processes taking place in the metal pipe during prolonged use. Studing the complex physical and mechanical properties to assess the resistance to the destruction of the metal in the environment closest to the operating conditions.
статья, добавлен 30.01.2016The role of coke gas cleaning in ensuring optimal operational productivity and compliance with environmental requirements in coke production. The influence of configurations and optimization of nozzle placement strategies on the quality of coke gas.
статья, добавлен 17.06.2024The concept and functional characteristics of diamond-like films of amorphous carbon with a high concentration of carbon with SP3. The peculiarities of their practical use. Diagram of the coating, its physical and chemical properties, the benefits.
статья, добавлен 12.06.2015Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019- 38. Chemical modification of aminopolysaccharide from shrimp shell by direct connection with polyaniline
Modification of aminopolysaccharide by deacetylation of chitin from the shrimp shell using the enzyme as a biocatalyst and microwave energy. The influence of temperature and reaction time, the ratio of aminopolysaccharide to aniline on its properties.
статья, добавлен 10.08.2020 The study of the Microbiology of the procedure of biological fermentation, physico-chemical characteristics of activated sludge of the Bortnichy station of aeration. Offer possible ways to increase the speed of the procedure of biological fermentation.
статья, добавлен 27.11.2016Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016The model of the disperse material behavior under vibration in the hole of the dispenser based on the Navier-Stokes equations. The influence of the power factor on the movement of the product and the parameters of the hole on the vibrating dosing process.
статья, добавлен 14.09.2016Wind turbine concept with air duct. Influence of the exit area and entry area on aerodynamic characteristics. Designing a new model of Invelox. The need to install a curtain at the end of the air intake to change the direction of the air flow up, down.
статья, добавлен 08.03.2021The elemental composition of the developed gerodietetic dry soluble product for enteral nutrition. The satisfaction level of older age group representatives average needs in mineral elements basing on the developed product in ready for usage liquid form.
статья, добавлен 14.02.2022Properties and structure of hydrocarbons. Types and communication aromatics. The nature of the relationship between the carbon atoms. The methods of extraction and processing of oil. The use of the rectification columns for fractionating of raw materials.
презентация, добавлен 30.06.2014The study of the influence of the surface hardness of the auger on its wear during dehydration of solid waste in the garbage truck. Usage of the method of regression analysis, the logarithmic dependencies of auger wear depending on the hardness.
статья, добавлен 23.06.2022The methods of defrosting frozen berries affect sensory characteristics and the indicator of cell juice loss of the resulting product. This method preserved the tissue strength of the berry surface completely, resulting in null loss of cell juice.
статья, добавлен 14.02.2025Determination of material properties of polymeric resins. Processing and finishing operations commonly used in the manufacture of plastic products. Analysis of relative differences in the coefficient of thermal expansion and modulus of elasticity.
статья, добавлен 10.03.2019Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019Research of mathematical model of the process intrusion forming polymer products. Establishing a dependency on the angle of melt costs lifting screw injection unit in the material cylinder based on the geometric parameters of extrusion head and mold.
статья, добавлен 18.02.2016Dynamic designer as a way to save time and cost of getting new products to market, and improving old ones without a huge investment in equipment. Using parametric solid models for to develop the form of the parts. Mechanical desktop to build prototypes.
презентация, добавлен 21.02.2014