Management and control of quality parameters of wear-resistant coatings
Learning algorithm of consistent actions to obtain quality coatings made by the complex technological method electrocontact strengthening of sprayed coatings. Analysis Ishikawa diagram which allows identify the causes of the impairment coatings obtained.
Подобные документы
Experimental heat treatment of coal from the Shoptykol deposit of the Maikuben basin by carbonization, activation in a pilot laboratory unit. Analysis of the adsorption characteristics of the samples. Approbation of the obtained activated carbon.
статья, добавлен 28.12.2020Adding ginger extract to the technology of table margarine production. Expanding the margarine market range and extending its shelf life. The effect of adding an additive on an organoleptic characteristics of margarine, giving it a spicy taste and aroma.
статья, добавлен 14.12.2024Analysis of the main causes of destruction of adhesive joints. Structural and technological stress concentrators, because of which cracks develop during operation. General characteristics of the resistance of adhesive bonding to failure at all stages.
статья, добавлен 30.04.2018Controlling the rudder, counting the distance traveled, turning off the engine and resetting the wings - the simplest autopilot functions. Radio control - the technology, that allows drones to follow difficult routes, perform maneuvers in the air.
статья, добавлен 27.02.2021- 105. Investigation of properties of the constant technological track, which is used in bridge agriculture
Mechanical properties of soil traces of a permanent technological track and their influence on the traction and traction properties of a bridge agricultural machine of a new design. The research was conducted using the provisions of the tractor theory.
статья, добавлен 30.08.2022 Classification level of development of new technologies in the BSR countries using a synthetic development measure. Grouping with the help of cluster analysis. Identify the most important features that determine their development and use as a roadmap.
статья, добавлен 28.09.2016Analysis of design features and parameters of automobile and aircraft engines is carried out. It is shown that car engines, despite the high technical level achieved at the beginning of the 21st century, do not technically meet aviation requirements.
статья, добавлен 19.06.2022Defining and analysis the essence of robot is an automatic device, which has a manipulator – mechanical analogue of human hand, and manipulator control system. Consideration and characteristic of the structural features model of domestic robot–helper.
статья, добавлен 29.01.2016Розробка плану впровадження системи аналізу небезпечних чинників та критичних точок контролю на молочноконсервному комбінаті з урахуванням принципів комбінування молочно-рослинної сировини. Аналіз виробничих ризиків та заходів щодо їх виникнення.
статья, добавлен 27.12.2016The relation between the particles velocity and the deposition efficiency of material powders. A different approaches for calculating the critical deposition velocity. Computational fluid dynamics model. Critical particle velocity determination.
статья, добавлен 29.11.2016Features of defining the basic principles of the formation of the "unisex" style direction as a design practice in clothing design. Analysis of ways to identify the design and artistic compositional properties of the development of a costume collection.
статья, добавлен 25.04.2022Nonaxisymmetric boundary value problem of elasticity theory for multiconnected body with cylindrical boundaries. Boundary conditions by the generalized Fourier method. The numerical analysis of stresses in the areas of their greatest concentration.
статья, добавлен 30.10.2016The present study is a mathematical modeling aimed at the dynamic force analysis of printed circuit boards in order to eliminate dynamic stresses to an acceptable level and ensure the strength and reliability of the printed circuit board design.
статья, добавлен 02.06.2022A resource-saving technology complex processing of highly mineralized mine waters of mining enterprises of the Kryvyi Rih iron ore basin has been developed. Of all the known methods of water desalination, the only method in this case is reverse osmosis.
статья, добавлен 26.12.2023Methodical approach to the determination of key parameters of rotary positioning units intended for manufacturing technology and robotics. The applicability of the selected methodology for measuring selected parameters of the uniaxial positioning table.
статья, добавлен 26.08.2020Examines the role of artificial intelligence, sensors, and other technological innovations in shaping and optimizing logistics processes in the United States. There are many new opportunities to innovate and improve efficiency and customer satisfaction.
статья, добавлен 21.03.2024The study of the formation mechanism of flavonoid complex with aluminum ions. On the basis of the negative low Gibbs free energy values it found that chelation is a natural phenomenon. Determination of the antioxidant capacity of flavonoids stevia leaf.
статья, добавлен 30.01.2016- 118. Principles of calculation of piezoelectric elements with surfaces partial covering by electrodes
Description of stress-strain state and transfer characteristics of piezoelectric elements with partial surfaces electrogalvanism. The power method of the analysis of the physical condition of the piezoelectric elements in the mode of forced oscillations.
статья, добавлен 30.08.2016 Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
статья, добавлен 21.12.2016The food industry is unthinkable without fundamental science that is without scientific researches, highly technological production systems. The updating of technologies, the creating of new for future food technologies on fundamental science discoveries.
статья, добавлен 25.06.2018Familiarization with layout of placement of guard signaling complex systems. Research technology of modeling discrete continuous stochastic systems. Characteristics of the main methods ensuring probability of successful fulfilment of seismic sensor.
статья, добавлен 30.01.2016Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019Definitions and models of control in water supply and sanitation industry. Concession model of control sanitation industry in international practice. Condition of networks and evolution of model. Research limitations and future research directions.
дипломная работа, добавлен 13.11.2015Comparison of two non-conventional processes which are laser and photochemical machining. The formation of complex shapes in metal sheets. Chemical etching of the material for the manufacture of the desired finished product by a controlled corrosion.
статья, добавлен 03.12.2015System for billet continuous caster’s mould heat engineering parameters monitoring. Formation of the internal heat transfer surfaces. Calculation the indicators: average heat flux density, overall heat exchange coefficient. Effective gas gap thickness.
статья, добавлен 30.01.2016