Properties of oil products
Properties and structure of hydrocarbons. Types and communication aromatics. The nature of the relationship between the carbon atoms. The methods of extraction and processing of oil. The use of the rectification columns for fractionating of raw materials.
Подобные документы
Comparison of the results of processing arrays light absorption alternate method of incorporating calibration surface with other methods. Determination of Ni2 +, Co3 +, Fe2 +, Cu2 + from 1-(2-pyridylazo)-2-naphthol in aqueous-micellar environment.
статья, добавлен 23.02.2016Results Global Capstone Design Workshop in order to find eco-friendly, energy-saving methods in our daily lives and to develop and improve them. In particular, selecting topics based on practical methods for Global Capstone Design will be the main focus.
статья, добавлен 20.09.2021These developments are devoted to the use of sol-gel processes in various branches of science and technology. Based on inorganic ion-exchange materials, a technology was developed to extract lithium from natural brines, which are poor in lithium content.
статья, добавлен 31.10.2017Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019Characteristics of jet fuels: general information and properties. Fractional composition: initial boiling point and 10% fuel distillation temperature, 50% fuel distillation temperature and temperature of 90 % fuel distillation (t90) and dry point.
контрольная работа, добавлен 06.12.2014Using transmission electron microscopy methods the layer by layer analysis of the bulk hardened superior quality rails is carried out, phase state and defect substructure gradients are established. Character of changing of structure-phase states.
статья, добавлен 30.07.2016The technology of polystyrene plastics. The application methods for industrial liquid coatings and finishes. The spraying, brushing, printing, and silk screening. The application methods for powder coatings and finishes. The electrostatic spray outfits.
статья, добавлен 10.03.2019Analysis of ideas about conducting an early assessment of emerging medical technologies. Developing medical products and services with added value. Determining the commercial viability of medical products and services in the early stages of development.
статья, добавлен 12.04.2022Gathering of materials about a petroleum industry in a museum creates favorable conditions for their protection. The assemblage of materials is stored In a museum about the factory "Brothers Nobel". The oil extracted by brothers Nobel in 1894-1903.
статья, добавлен 03.03.2018The recent work on Micro Aerial Vehicles (MAV) at the Institute of Aerospace Systems. Basics of MAV Research. Flightmechanical simulation. Wind tunnel tests. Overall controller system structure. The inertial measurement unit. On-Board computer structure.
творческая работа, добавлен 18.01.2014The study investigates the kinematics of robots with the aim of expedient use of certain engineering solutions solving certain problems related to the accuracy of robot movement. The object of study is various types of robots and their kinematic systems.
статья, добавлен 20.07.2024Presents various methods of piling, using undercutting, as well as various combinations of these methods. The impact load on the pile head is created by special mechanisms. Driving piles by screwing is based on driving steel and reinforced concrete.
статья, добавлен 10.10.2024Special supervisory control system responsible for the informative data acquisition about the current enterprise production and its control. The main SCADA. The general structure of SCADA. The Three main structure components modern SCADA-systems.
статья, добавлен 30.04.2019The obstacle in the way of nanotechnologies is the lack of selective "scalpel and forceps", the instruments to operate with particles of size less than 10-9 meters, particularly with molecules and atoms. Atomic forceps and scalpel for nanotechnologies.
статья, добавлен 29.12.2023The two main methods of mechanical assembly of plastic parts. Requirements for reliable mechanically bonded plastic joints. Special consideration for composites. The main advantages and disadvantages of adhesive bonding (gluing or glue bonding).
статья, добавлен 10.03.2019The conductive nanocomposite films on the basis of reactionary copolymers received. The threshold of their percolation is determined. It was shown that its value depends on the size of specific surface of nanotubes and conditions of composite obtaining.
статья, добавлен 23.09.2016Development of methods for heat engineering tests of hydrodynamic pumps. Processes which occur in activator with water thermal hydrodynamic pump. Water flow speeds in a system. Gas bubbles are the product of centrifugal force effecting on carrier flow.
статья, добавлен 01.08.2016Study of emotional intelligence. Research of emotional intelligence of primary school children and features of emotional intelligence of children separated from their parents. Relationship between the level of emotional intelligence, sociometric status.
статья, добавлен 12.11.2022The analysis of the cement production process in Ghana, which is limited to grinding clinker into cement and its packaging and distribution. The equipment of grinding chains, the best configuration. Control methods used for cement grinding chains.
статья, добавлен 30.05.2018Thermosetting plastics, their irreversible chemical reaction (polymerization), including the effects of temperature and time. Bringing the resin composition to a liquid state, forcing the liquid to flow into the cavity of the desired configuration.
статья, добавлен 10.03.2019Defining features of the motion of moving the controls in vibroudarnogo qualifier. Analysis of the effectiveness and efficiency of processing of minerals. Creating an analytic function, which could describe the trajectory of the mass center of the rink.
статья, добавлен 24.02.2016Image processing of assembly parts at specified automated line from FESTO company to automate monitoring and evaluating of obtained data together with supporting of educational activities for field: "automation and control of machines and processes".
статья, добавлен 26.08.2020Analysis of the aspects of the specifications and drawings of plastics that are specific to this family of materials and processes and that are related to the realities that need to be taken into account. Cavity identification and rough indication.
статья, добавлен 10.03.2019The developing of the numerical model of viscoelastic material using finite element method. The comparison of the obtained results with use of FEM software with experimental data. The calculation of the stress and strain state of the asphalt specimen.
статья, добавлен 29.09.2016Improving matching techniques constructional and technological parameters of the installation with the modes of its work taking into account the features of the resonator. The changes in the dielectric parameters of raw material during the heat treatment.
автореферат, добавлен 30.04.2018