Peculiarities of polyethyleneoxide solution streaming through jet-shaping head while cutting foodstuffs
The regularities of macromolecules behavior in the flow with longitudinal velocity gradient and manifested in this case effects of elastic deformations have importance in understanding the mechanism of anomalously high cutting power of water-polymer jet.
Подобные документы
The deals with the consideration of the peculiarities of the translation of English phraseological units on the basis of media discourse. It was found that phraseological combinations are stable, where one of the components has an independent meaning.
статья, добавлен 27.12.2023Analysis of requirements for electric-drive of mechanism of pulsed wire feed, and the benefits of using a special Brushless Direct Current electric-drive. Design of half-bridge circuit to regulate the strength of the current phase of the stator windings.
статья, добавлен 22.12.2016Determination of torque on the shaft of auger intensifier, power consumption, energy intensity and productivity of the backfilling workflow. Evaluation of soil properties, geometric parameters of the screw intensifier and speed of the bulldozer.
статья, добавлен 01.12.2017The types of mechanisms turning and folding blades used for power control and stabilization of frequency of rotation of the wind turbines. The dependence of the displacements of sliders and centrifugal weights on the angle of rotation of the blade.
статья, добавлен 14.09.2016The antibacterial effect of chitooligosaccharides, evaluated against various microorganisms. The oligosaccharides from chitosan and fractionated with ultrafiltration membrane and enzymatic bioreactor. The molecular weight of chitooligosaccharides.
реферат, добавлен 07.09.2011Experimental improvement of the stability of the bolt connection of the technological and power modules of the new design of the modular machine-tractor unit. The new construction of the pivot connection of the technological module with the power module.
статья, добавлен 10.08.2022Model for calculation of nominal stresses in characteristic points of the surface fatigue crack to the tubular shaft in bending with rotation. Reasons for the decrease of the propagation velocity of cracks in the center and changing the geometry.
статья, добавлен 28.09.2016The conductive nanocomposite films on the basis of reactionary copolymers received. The threshold of their percolation is determined. It was shown that its value depends on the size of specific surface of nanotubes and conditions of composite obtaining.
статья, добавлен 23.09.2016The establishment of unfavorable modes of operation of mining equipment under which there is an unstable position in space of the suction head during its descent to the bottom. The influence of hydrostatic pressure on the strengthening of the digging.
статья, добавлен 30.07.2016The need to design new drilling equipment. The analyzed existing options for solving the problem solve it to some extent. To eliminate them, it is proposed to use elastic elements (ring springs) in the construction of double-shoulder tool joints.
статья, добавлен 02.03.2021The main advantages and disadvantages of well-known spiral drills with a multi-stage blade. It is described that the bridge, together with the steps adjacent to the grooves, is a small centering drill, performs centering and drilling during the process.
статья, добавлен 10.02.2021Analyzed the impact of long-term operation of gas pipelines, as well as natural stress concentrators on the physico-mechanical properties of welded joints of steel 17G1S. Regularities of the destruction of the material of welded joints of gas pipelines.
статья, добавлен 30.01.2016Improving the method of dynamic analysis of mechanical systems dynamic factors dynamic model which can be represented by three-mass system of row with the first driving mass with prestressing elastic drive connections. Finding the dynamic coefficients.
статья, добавлен 30.07.2016Biodegradable poly-3-hydroxybutyrate [P(3HB)] and birch sawdust - a material for the preparation of powder mixtures for molds in the production of granules and tablets. The prospect of a composite obtained on this basis for the building industry.
статья, добавлен 17.04.2022Production polystyrene composite films with small content of fullerenes (up to 1 %) by casting o-xylene solutions. A dependence of the glass transition temperature of the composite material on its composition. The adsorption capacity of polymer material.
статья, добавлен 30.07.2016Various kinds of mathematical models of a snakelike robot motion depending on gait pattern. Simplified model of a snake. The motion sequence of three-mass system. The average velocity depending on number of masses. Determination of optimal masses number.
статья, добавлен 27.08.2020Расчет элемента трубопровода при помощи Flow Simulation в пакете SolidWorks. Характеристика исследования влияния размеров и формы воздуховодов на равномерность воздушного потока и сопротивление в вентиляции системы охлаждения тяговых электродвигателей.
контрольная работа, добавлен 17.09.2015Consideration the mathematical model of process of pressing of seamless pipes. Effect on various forms of rolling shaping matrix. The nature of the formation of the deformation zone. Development of direct compression on a cylindrical mandrel pipe.
статья, добавлен 30.01.2016Понятие и особенности конструкции Warka Water, его внутреннее устройство и принцип действия, роль и значение в обеспечении водой засушливых регионов. Kafon как инновационное устройство для детонации мин. Разработка и сферы использования аэрогеля.
реферат, добавлен 19.10.2016Features of the application of methods for monitoring the state of the wooden structure in the production flow. Ways to optimize the prediction of wood properties using various NDE methods. The combination of methods for effective quality control of wood.
статья, добавлен 29.11.2018Search for ways to reduce emissions of pollutants. Biomass as a composite material. Laboratory installation for glucose fermentation to ethanol. Study the concentration of xylose as a function of time. Process flow diagram of the synthesis of bioethanol.
статья, добавлен 23.06.2018Ansys Workbench как одна из основных оболочек программного инженерного комплекса ANSYS. Моделирование и определение гидродинамических и технических параметров потока жидкости в трубопроводе. Создание в среде Fluid Flow торроидального осевого вихря.
статья, добавлен 09.02.2021Studies of Heat and Mass of drying in the process for the production of slag gravel. Determination of the temperature of the thermal agent at the height of the layer of materials. The dependence of the velocity of the mass transfer of temperature zones.
статья, добавлен 24.02.2016The historical and formation stages of the Lviv school of glassmaking are approximated. The modernization of educational mechanisms are identified, ways of their solution are suggested and applied measures that will promote implementation are outlined.
статья, добавлен 16.02.2022Дослідження струменево-променевого різання твердих тіл з використанням лазера потужністю 400 Вт із широким діапазоном регулювання тривалості імпульсу та енергії. Вплив високошвидкісного потоку рідини малого діаметру на умови охолоджування в зоні різання.
статья, добавлен 05.12.2013