Surveillance and endurance micro air vehicles
Development of flexible-wing Micro Air Vehicles at the University of Florida. Design intent and approach, identifying airplane components, fabrication techniques and various testing methods used to assess overall airplane and component performance.
Подобные документы
Assessing the development of the global economy and aerospace industry. Finding ways to reduce environmental pollution, energy consumption and flight costs. Increasing the thrust-to-weight ratio, safety and reliability of modern aircraft engines.
статья, добавлен 20.07.2024Digital technologies are a modern challenge that has changed global economic processes, infrastructure and business environment. Studying the features of the digital business environment in Georgia and identifying opportunities for its improvement.
статья, добавлен 19.03.2024Improving matching techniques constructional and technological parameters of the installation with the modes of its work taking into account the features of the resonator. The changes in the dielectric parameters of raw material during the heat treatment.
автореферат, добавлен 30.04.2018Hydrothermal sol-gel synthesis of hexagonally ordered silicas using a hybrid template system is reported. Silicas were characterized by IR spectroscopy, X-ray diffraction techniques as well as electron microscopy. The hexagonal structure of MCM-41.
статья, добавлен 30.07.2016Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019Способы промышленного получения изопропилбензола. Химизм и механизм реакции алкилирования. Термодинамика и кинетика процесса. Описание программных сред, используемых для моделирования химических производств. Разработка модели ректификационной колонны.
курсовая работа, добавлен 26.10.2020The paper presents the design of experimental cells, a description of materials for construction and construction process, and preliminary results. The objective of the work is proving which of the MBT fractions function better for methane degradation.
статья, добавлен 08.10.2020The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
магистерская работа, добавлен 14.02.2013Motion systems as core technologies, as mechanical systems, like microelectronic manufacturing equipment, are required to achieve high speed and accuracy. The influence of the dynamics of a mechanical system on the quality of the position tracking syste
статья, добавлен 26.08.2020Deployment of two-arm robots in different plants. Designing of an educational workplace for assembly, equipped with a two-arm robot. Using of Schunk electric grippers to adjust the range of movement and clamping force. Design a robotic workplace.
статья, добавлен 28.08.2020Обобщение экспериментальных данных по выбору органического растворителя в промышленном производстве йодметилата с применением принципов концепции "Quality by design". Эффективность использования растворяющих веществ для синтеза и кристаллизации.
статья, добавлен 26.07.2016Evaluation of the technical system and its subsequent use for decision-making to ensure complex technical systems with appropriate quality of work. The characteristics and specificity of the model changes performance States based on the Markov chain.
статья, добавлен 29.01.2016Types of Electric Vehicle in use Today. Alternative and Novel Energy Sources and Stores. Electric Machines and their Controllers. Motor Cooling, Efficiency and Mass. Design of Ancillary Systems. Battery powered cars and vans. Torque speed characteristics.
книга, добавлен 25.11.2013A divider for planar antennas is considered. Diffraction problems for junctions of planar waveguides with infinitely thin walls and for walls with finite thickness are considered in the article. Some important for design numerical results are presented.
статья, добавлен 04.11.2018Dynamic designer as a way to save time and cost of getting new products to market, and improving old ones without a huge investment in equipment. Using parametric solid models for to develop the form of the parts. Mechanical desktop to build prototypes.
презентация, добавлен 21.02.2014Geometry, FE analys, optimization, mechanisms, plastics and MSC/ARIES positioning for design detail. Full function ACIS based modeler, constraints, region operator to sub-divide geometry. Pre release solids shelling, per face (uniform) thickness control.
презентация, добавлен 21.02.2014Analysis of design features and parameters of automobile and aircraft engines is carried out. It is shown that car engines, despite the high technical level achieved at the beginning of the 21st century, do not technically meet aviation requirements.
статья, добавлен 19.06.2022Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016Calculation of the coefficients autopilot unit for homing rockets based on genetic algorithms in which the autopilot block (AB) quality parameters are considered as the criterion for evaluating the optimality of the AB. Optimality of AB coefficients.
статья, добавлен 30.04.2018- 95. Finding the conditions of hydrocarbons safe storing and transportation in tanks of different shapes
Application of the software package ConvEx in the design of storage tanks for petroleum products prone to self-degradation. Investigation of the influence of the geometric shape of the vessel on the critical temperature of storage of petroleum products.
статья, добавлен 10.05.2018 Creation of a 3D model of the design scheme of the water heating and cavitation device and simulation in Hysys software. The main relationships between temperature, pressure and flow rate of the cavitation generator of the pulse hydrocycle unit.
статья, добавлен 10.12.2024Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
статья, добавлен 10.03.2019The use of the boundary values of parameters of mould displacement of the earth's surface and refining the workings of the design scheme to predict the trajectory of sedimentation. Determination of empirical coefficients of mathematical equations.
статья, добавлен 30.07.2016- 99. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 The deals with the consideration of the peculiarities of the translation of English phraseological units on the basis of media discourse. It was found that phraseological combinations are stable, where one of the components has an independent meaning.
статья, добавлен 27.12.2023