Influence of the nature of surface-active substances on rheology of high-filled pastelike compositions on a base on liquid diene rubber and disperse filler
Studies on the preparation of pasty high-filled compositions and evaluation of their rheological properties using a rotational visco-meter "Reotest-2" on the cone-plane system. Evaluation of sedimentation resistance of compositions and their flow.
Подобные документы
Evaluation of the relevance of Vernadskyi's noosphere concept. Transformation of the biosphere by man with the help of the mind. Development in the direction of the creation of technical subjects and replacement of the biosphere with the technosphere.
статья, добавлен 18.04.2023Analysis a lot of problems which constrain the transfer of diesel engines on "ecological" fuel and showing opportunities of manufacturing this fuel on Ukrainian enterprises. Evaluation of innovation taking in consideration environmental protection.
статья, добавлен 13.09.2016Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Analysis of the main causes of destruction of adhesive joints. Structural and technological stress concentrators, because of which cracks develop during operation. General characteristics of the resistance of adhesive bonding to failure at all stages.
статья, добавлен 30.04.2018The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
магистерская работа, добавлен 14.02.2013Wind turbine concept with air duct. Influence of the exit area and entry area on aerodynamic characteristics. Designing a new model of Invelox. The need to install a curtain at the end of the air intake to change the direction of the air flow up, down.
статья, добавлен 08.03.2021Comprehensive analysis of allelic protein variants suitable for use in bakery products made from Iraqi wheat varieties, as well as biological evaluation of these varieties using a genetic source using a general method of qualitative grain selection.
статья, добавлен 18.03.2021Analysis of the selective adsorbent. Influence of modifying pentasyl group synthetic zeolites (Silicalite-1 and Silicalite-2) with metal cations capable to specific interactions on the separation ability of the chromatographic column has been studied.
статья, добавлен 02.04.2014The quantization error functional. invariant regularizers. A regularized quantization functional. The connection to the GTM. Uniform convergence bounds and hence bounds on the learning rates of the algorithm. Experiments and evaluation of their results.
статья, добавлен 08.02.2013Rationale for the use of advanced technology for sewage treatment schemes dairies. Removal of insoluble organic matter by adding a flotation purification scheme. Using the immersed biofilter for a disk intensive degradation of organic pollutants.
статья, добавлен 13.08.2016Сопоставлены данные о гидродинамике реального потока смоделированного в программе SolidWorks Flow Simulation в эмульсоре вихревого типа, в центральной части камеры энергетического разделения которого, создается зона пониженного давления - зона кавитации.
статья, добавлен 02.01.2025The compositional analysis of wastes and finding environmentally sustainable and innovative alternatives for waste disposal for tanneries. The processing and evaluation of hydrolyzed collagen and skin waste for the realization of composite materials.
статья, добавлен 24.02.2025Scientific justification for automated control method of optimal charge of pebble mill operating in series with a magnetic separator in the second stage of crushing in magnetic separating plants that process on iron ores with varying physical properties.
статья, добавлен 23.03.2016- 89. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 Types of tool materials: from high-carbon steel to ceramics and diamonds, and their use as cutting tools in the modern metal industry. Cutting tool and its characteristics: hardness, strength. Achieving an acceptable tool life before replacing it.
статья, добавлен 26.04.2019Optical properties of nanocomposites are important and useful in their consumer satisfaction capacities. In this research, coloration properties of dyed PA6/Nano TiO2 nanocomposite is studied using a combined Mie and Kubelka-Munk light scattering theory.
статья, добавлен 30.07.2016Study of the main tasks of industrial enterprises. A number of key factors affecting production. Ways to ensure production of high-quality products necessary for society, ways to improve production indicators based on increasing production efficiency.
статья, добавлен 26.02.2023- 93. Chemical modification of aminopolysaccharide from shrimp shell by direct connection with polyaniline
Modification of aminopolysaccharide by deacetylation of chitin from the shrimp shell using the enzyme as a biocatalyst and microwave energy. The influence of temperature and reaction time, the ratio of aminopolysaccharide to aniline on its properties.
статья, добавлен 10.08.2020 Determining the effect of coating thickness on Hardness which is used on the protective layer when polyester coating is applied on the aluminum coil. Determining the scratch hardness using Hardness pencils test according to Wolff-Willborn "ASTM D3363".
статья, добавлен 06.05.2018- 95. Global Research on Artificial Intelligence from 1990–2014: Spatially-Explicit Bibliometric Analysis
The evaluation of artificial intelligence research from 1990–2014 by using bibliometric analysis. Growth trend of articles in artificial intelligence from. Temporal pattern of frequently used keywords. International Productivity and Collaboration.
статья, добавлен 02.02.2017 Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016Analysis of the development of the basic methods of engineering the contact surfaces of tribological systems. Characteristics of the problems and prospects of development of technologies of creating surfaces of discrete-oriented structure of the system.
статья, добавлен 18.02.2016Аналіз методики та результатів математичного моделювання з використанням пакету Flow Vision процесів течії в’язкої рідини в вузькому проміжку між циліндричним електродом-дротом та пласкою поверхнею заготовки при коаксіальній подачі струменю промивки.
статья, добавлен 11.10.2013- 99. The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
статья, добавлен 29.01.2016 Investigation of multilayer coatings with different bilayer periods 8-100 nm. Using of very thin layers in multilayered system leads to increasing of specific density of interphase boundaries and it leads to increasing of critical loading of destruction.
статья, добавлен 30.07.2016