To a question of forecasting of firmness of foundry equipment
Features the design of tooling for casting under pressure of zinc alloys. The problem that arise when designing a press-forms of analysis. Experiments to study thermal stability of materials, parts, equipment subject to cyclic thermo-mechanical treatment.
Подобные документы
Study the effects of man-made nano-additive on basic physical and mechanical properties of foamed glass. Use tare and flat glass as the main raw material. Investigation the effect of nano-additive on structural features of the resulting foam glass.
статья, добавлен 30.07.2016The Safety Experience Center where you can create a space where you can experience a virtual disaster, learn how to survive, and find alternatives that can increase your viability the most. In order to commemorate the tragedy of the "Sewol ferry".
статья, добавлен 12.05.2024Structure of three-cone rock bit with inserted hard-alloyed rock-destruction and protecting equipment, in which the chief components are marked. The minimally possible set of operators, which support qualitative performance of technological process.
статья, добавлен 14.09.2016The use of metallic pigments with features of the geometry of the surface of printing materials. Functionality of the "Materials Editor" program and a group of parameters of geometric surface structures. Assessment of surface structures in the 3D system.
статья, добавлен 12.06.2023The flexural and compressive strength of mortar by partial replacement of cement with Nano-ZnO particles has been studied. The results showed that the flexural and compressive strength of the cement mortars with ZnO were higher than pure cement mortar.
статья, добавлен 12.06.2018The optimization procedure in computer-aided design problem. The methodic of optimal weight coefficients values choice. The use of structural models in the form of tables and morphological trees of quality variants of the signs of aerial vehicles.
статья, добавлен 14.09.2016Analysis of design features and parameters of automobile and aircraft engines is carried out. It is shown that car engines, despite the high technical level achieved at the beginning of the 21st century, do not technically meet aviation requirements.
статья, добавлен 19.06.2022Analysis and comparison of the different rotor type permanent magnet machines. The presented machines are designed as having same geometrical dimensions and same materials for comparison. Permanent magnet machines, mathematical modeling, motor geometry.
реферат, добавлен 25.03.2011Biodegradable poly-3-hydroxybutyrate [P(3HB)] and birch sawdust - a material for the preparation of powder mixtures for molds in the production of granules and tablets. The prospect of a composite obtained on this basis for the building industry.
статья, добавлен 17.04.2022Study of features of lysergic acid diethylamide opening. Characteristic aspects of cornflakes in the United States. Analysis of the background of the invention of the pacemaker. Characteristics based on the version of the discoverer of anesthesia.
презентация, добавлен 16.11.2013A study of the collections of young Moldovan designers, graduates of the KSPU. I. Kryanga. Conceptual trends in the contemporary art of design and fashion in the country, based on the creative interpretation of artistic images by young designers.
статья, добавлен 22.05.2022Deployment of two-arm robots in different plants. Designing of an educational workplace for assembly, equipped with a two-arm robot. Using of Schunk electric grippers to adjust the range of movement and clamping force. Design a robotic workplace.
статья, добавлен 28.08.2020A modern house built using materials that "smell of the past, but strive for the future." The use of mechanical ventilation with dehumidification, radiant floor, photovoltaic panels with energy storage and heat pump. Creating a comfortable temperature.
статья, добавлен 04.10.2021Creation and testing of a model of a diesel engine muffler. Plotting a pressure level diagram inside the device. Analysis of the distribution of the sound field. Assessment energy losses of exhaust gases. Estimation of the spectrum and octave bandwidth.
статья, добавлен 10.10.2024The present study is a mathematical modeling aimed at the dynamic force analysis of printed circuit boards in order to eliminate dynamic stresses to an acceptable level and ensure the strength and reliability of the printed circuit board design.
статья, добавлен 02.06.2022The results of experiments on the processing of low-grade Vyatka-Kama phosphate for alkaline phosphoric fertilizer using different industrial wastes. Available to get the thermal phosphate with the content of sulfate-soda mixture and organic sludge.
статья, добавлен 30.04.2018Cylinder shaped parts – one of the mostly used in printing presses. A new technology of strengthening and recovery of details based on vibration roll burnishing is offered in the article. Experimental work and scientific conclusions are described.
статья, добавлен 29.07.2016Development of methods for heat engineering tests of hydrodynamic pumps. Processes which occur in activator with water thermal hydrodynamic pump. Water flow speeds in a system. Gas bubbles are the product of centrifugal force effecting on carrier flow.
статья, добавлен 01.08.2016Reduce costs and increase durability of threaded connections. The relationship between the thermal treatment and the strength of the threaded connection. Compare the minimum tightening hermetic threaded connections three types of anaerobic adhesives.
статья, добавлен 28.09.2016Determination of torque on the shaft of auger intensifier, power consumption, energy intensity and productivity of the backfilling workflow. Evaluation of soil properties, geometric parameters of the screw intensifier and speed of the bulldozer.
статья, добавлен 01.12.2017The method of reducing costs and increasing the strength of threaded joints, which are currently used in every field of human activity. Experimental research on the relation between thermal treatment and strength of adhesively sealed joints was con
статья, добавлен 28.09.2016Analysis of the evolution of approaches to the design of viable complex systems and the formation of the principles of hybrid thinking of designers on a transdisciplinary basis. Formation of the engineering design thinking as a means of adaptation.
статья, добавлен 15.09.2024The relation between the particles velocity and the deposition efficiency of material powders. A different approaches for calculating the critical deposition velocity. Computational fluid dynamics model. Critical particle velocity determination.
статья, добавлен 29.11.2016Nanocomposites comprising ray in a polymer. The reflection mechanical properties material. Increasing the polymer properties by forming the interphase. Obtaining curves of stress-strain states of macroscopic samples irradiated polymer materials.
статья, добавлен 30.07.2016Wind turbine concept with air duct. Influence of the exit area and entry area on aerodynamic characteristics. Designing a new model of Invelox. The need to install a curtain at the end of the air intake to change the direction of the air flow up, down.
статья, добавлен 08.03.2021