Characterization of semiconductor materials. Principles and Methods
An analysis of demand in the semiconductor industry, covering all three phases of materials: gases, liquids and solids. The study of the peculiarities of application for solids which includes a semiconductor substrate, metal, dielectric, an organic film.
Подобные документы
The comparative analysis of the microstructure, phase and chemical composition of the experimental alloys of the Fe-W type with the standardized grade ferrotungsten. The feasibility of using Fe-W for the manufacture high tungsten materials based on iron.
статья, добавлен 30.01.2016Models which adequately combine technological parameters with indicators of treatment quality have been designed for the cavitation cleaning processes of sewage from organic admixtures. Water of industry and public water use it is considered as sewage.
статья, добавлен 14.09.2016The concept and functional characteristics of diamond-like films of amorphous carbon with a high concentration of carbon with SP3. The peculiarities of their practical use. Diagram of the coating, its physical and chemical properties, the benefits.
статья, добавлен 12.06.2015- 29. The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
статья, добавлен 29.01.2016 Geometry, FE analys, optimization, mechanisms, plastics and MSC/ARIES positioning for design detail. Full function ACIS based modeler, constraints, region operator to sub-divide geometry. Pre release solids shelling, per face (uniform) thickness control.
презентация, добавлен 21.02.2014Принцип работы винтового забойного двигателя. Система очистки буровых растворов на базе центрифуги. Центрифуга для очистки буровых растворов серии GNLW Solids Russia. Декантерная центрифуга HAUS DDE 2342 и ОГШ 202К-03. Расчет параметров центрифуги.
курсовая работа, добавлен 26.03.2024- 32. Principles of calculation of piezoelectric elements with surfaces partial covering by electrodes
Description of stress-strain state and transfer characteristics of piezoelectric elements with partial surfaces electrogalvanism. The power method of the analysis of the physical condition of the piezoelectric elements in the mode of forced oscillations.
статья, добавлен 30.08.2016 The manufacturing industry may be a key sector for the application of this technology, reduce the use of conventional energy sources, especially in the food industry located in the Andean region. Ecuadorian policies and regulations on renewable energy.
статья, добавлен 23.07.2021Analysis of the aspects of the specifications and drawings of plastics that are specific to this family of materials and processes and that are related to the realities that need to be taken into account. Cavity identification and rough indication.
статья, добавлен 10.03.2019Production polystyrene composite films with small content of fullerenes (up to 1 %) by casting o-xylene solutions. A dependence of the glass transition temperature of the composite material on its composition. The adsorption capacity of polymer material.
статья, добавлен 30.07.2016Features of the application of methods for monitoring the state of the wooden structure in the production flow. Ways to optimize the prediction of wood properties using various NDE methods. The combination of methods for effective quality control of wood.
статья, добавлен 29.11.2018The study of structural changes during hot deformation metal during controlled rolling. The influence of preheating temperature and deformation degree on the size and shape of austenite grains. The definition of the polygonal structure of the austenite.
статья, добавлен 30.01.2017The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
магистерская работа, добавлен 14.02.2013Environmental biotechnology study the use of living organisms for a wide range of applications in hazardous waste treatment and pollution control. The use of biotechnology in the dairy industry. Methods for producing whey. Security staff activity.
курсовая работа, добавлен 13.04.2015Determining the effect of coating thickness on Hardness which is used on the protective layer when polyester coating is applied on the aluminum coil. Determining the scratch hardness using Hardness pencils test according to Wolff-Willborn "ASTM D3363".
статья, добавлен 06.05.2018Analysis of finite element methods, numerical methods for solving engineering and mathematical physics. Obtaining analytical solutions for problems of complex geometry, loads and material properties. Tension rods, beams and other simple structures.
презентация, добавлен 20.10.2014Consideration the processes taking place in the metal pipe during prolonged use. Studing the complex physical and mechanical properties to assess the resistance to the destruction of the metal in the environment closest to the operating conditions.
статья, добавлен 30.01.2016Creation and testing of a model of a diesel engine muffler. Plotting a pressure level diagram inside the device. Analysis of the distribution of the sound field. Assessment energy losses of exhaust gases. Estimation of the spectrum and octave bandwidth.
статья, добавлен 10.10.2024Class of application of heat pumps in industry. Review of the carbon dioxide heat pump in the transcritical cycle of operation according to the expander-ejector scheme. Development of methods for selecting control valves for a given heat pump circuit.
статья, добавлен 02.02.2019Analysis and comparison of the different rotor type permanent magnet machines. The presented machines are designed as having same geometrical dimensions and same materials for comparison. Permanent magnet machines, mathematical modeling, motor geometry.
реферат, добавлен 25.03.2011Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
статья, добавлен 21.12.2016The key advantages of applying ultrasonic technology at the collection dairy. The general principles of measurement of liquids' properties by Ultrasonic standing wave resonator. The monitoring of the milk quality. The benefits of using cylindrical waves.
статья, добавлен 15.04.2015The effect of casein-stabilized metal and metal oxide nanoparticles on the in vitro growth of Scoparia dulcis L. was studied. The effect of nanoparticles on callus induction, regeneration of shoots and roots was studied. Influence on the regeneration.
статья, добавлен 14.04.2022The study of magnetron sputtered coatings on base AlN-TiB2(TiSi2). The structural composition, morphology coated materials. Features amorphous-like coatings AlN-TiB2(TiSi2) after annealing and their impact on physical and mechanical properties changes.
статья, добавлен 30.07.2016The development of scientific and methodological bases of forming of structural and phase composition of alloys synthesized by the combined processes which consist of the metallothermic stage and SHS (self-propagating high-temperature synthesis).
статья, добавлен 07.09.2022