Kinematic analysis of centrifugal and aerodynamic mechanisms of blades turning and folding of horizontal-axis wind turbines
The types of mechanisms turning and folding blades used for power control and stabilization of frequency of rotation of the wind turbines. The dependence of the displacements of sliders and centrifugal weights on the angle of rotation of the blade.
Подобные документы
Computer-aided system as a solution of the computer-aided design task. Aerodynamical aspects of vertical-axis wind turbines. Principle of action of lift-driven vertical axis wind turbines. Formulation of the methodical basis for computer program.
статья, добавлен 14.09.2016The electric drive of Crane mechanisms. The powered motor speed control via frequency converter and process control via programmable logic controller. Cranes are an important part of many industries and construction sites used for lifting heavy loads.
статья, добавлен 14.02.2025The mechanisms used in industrial enterprises, crane mechanisms are one of the most common. This overhead cranes, which are the main types of crane mechanisms. For the optimal choice of electric drive, the basic requirements were taken into account
статья, добавлен 14.02.2025- 4. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 The study investigates the kinematics of robots with the aim of expedient use of certain engineering solutions solving certain problems related to the accuracy of robot movement. The object of study is various types of robots and their kinematic systems.
статья, добавлен 20.07.2024Appointment, device and action of the turning machine. Types of lathes, depending on the application. Metal processing on machine tools, turning operations. The use of water energy to drive. The principle of operation of the hydroelectric station.
статья, добавлен 11.03.2019The control station is designed for the control and smooth adjustment of the rotation frequency of the shaft of the alternating current electric motor depending on the operating characteristics of the technological equipment of the rod depth pump units.
статья, добавлен 10.12.2024- 8. Analysis of schemes of a current limiting unit in automatic control systems for dc electric drives
The most suitable electric drive for these mechanisms is considered to be a direct current electric drive with thyristor automatic control. Frequency control of asynchronous electric drives finds less application due to the complexity of control.
статья, добавлен 14.02.2025 Technical characteristics of the new turning and milling machines, the CTX beta 2000 TC. Milling with up to 220 Nm of torque (CTX beta-TC max. 120 Nm). Innovative multi-channel programming with ShopTurn 3G. The main advantages of CTX beta 2000 TC.
презентация, добавлен 29.11.2015Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016The Safety Experience Center where you can create a space where you can experience a virtual disaster, learn how to survive, and find alternatives that can increase your viability the most. In order to commemorate the tragedy of the "Sewol ferry".
статья, добавлен 12.05.2024Controlling the rudder, counting the distance traveled, turning off the engine and resetting the wings - the simplest autopilot functions. Radio control - the technology, that allows drones to follow difficult routes, perform maneuvers in the air.
статья, добавлен 27.02.2021Consideration of the characteristics of semantic modeling. Analysis of passivity-based switching control for stabilization of wheeled mobile robots. Features optimal kinodynamic motion planning for 2D reconfiguration of self-reconfigurable robots.
книга, добавлен 09.04.2013Renewable energy is energy obtained from solar, wind, wave, geothermal energy, water and other renewable sources. At this time, processes that are constantly occurring in nature are used, and these resources cannot be exhausted as a result of human use.
статья, добавлен 14.02.2025Consideration and characteristics of the scheme double-point wheel-rail interaction. Familiarization with the erosive wearing. Definition of the dependence of the coefficient of adhesion on the temperature. Analysis of sand system of the locomotive.
статья, добавлен 26.09.2016Wind turbine concept with air duct. Influence of the exit area and entry area on aerodynamic characteristics. Designing a new model of Invelox. The need to install a curtain at the end of the air intake to change the direction of the air flow up, down.
статья, добавлен 08.03.2021Proposes a method to increase information content in studying frequency properties of automatic control systems typical dynamic links based on representation of the link transfer functions in the form of graphs. Examples of separate links are provided.
статья, добавлен 25.01.2022Modernization of the transport system of the production system MPS 500. Creation of a new control program in the environment of the TIA portal. The main functions of the frequency converter. Investigation of the final state of the control cabinet.
статья, добавлен 26.08.2020Problems of hardware configuration in systems for stabilization of information and measuring devices operated at vehicles of wide class in difficult conditions of disturbances action. Analysis of modern devices and units used in stabilization systems.
статья, добавлен 14.09.2016Discussing an innovative technology for fault detection of the pipelines transportation. Study and characteristic repeated correlation of the above structures with kinematic diagram of failure, which make for adequate predicting the remaining life.
статья, добавлен 02.11.2018The main advantages and disadvantages of well-known spiral drills with a multi-stage blade. It is described that the bridge, together with the steps adjacent to the grooves, is a small centering drill, performs centering and drilling during the process.
статья, добавлен 10.02.2021Modeling and principle of operation positioner power consumption in the direct mode of automated management. Evaluation of the use of the corrected function decline in electricity consumption in the automated control system of technological process.
статья, добавлен 28.02.2016The service designed to facilitate the process of SCs, with demonstrating its elements in particular, database and knowledge base, arrangement of information for various users. In the authors’ opinion, such services will become a step towards no sphere.
статья, добавлен 13.10.2022Geometry, FE analys, optimization, mechanisms, plastics and MSC/ARIES positioning for design detail. Full function ACIS based modeler, constraints, region operator to sub-divide geometry. Pre release solids shelling, per face (uniform) thickness control.
презентация, добавлен 21.02.2014Theoretical studies allow developing a theoretical substantiated method for calculating the stability of spray vortex countercurrent mass transfer device. Review and characterization of the effect on the drop centrifugal force and resistance forces.
статья, добавлен 14.07.2016