Comparative studies on physico-chemical properties of indium sulfide films deposited under different deposition conditions by chemical bath deposition
Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
Подобные документы
The work of complex heat-recovery systems using water-hiting and air-heating heat-recovery exchangers was investigated. The combined use recovered heat to heat the return heat-network water, water of chemical water-purification system or combustion air.
статья, добавлен 22.04.2021The key advantages of applying ultrasonic technology at the collection dairy. The general principles of measurement of liquids' properties by Ultrasonic standing wave resonator. The monitoring of the milk quality. The benefits of using cylindrical waves.
статья, добавлен 15.04.2015Research of the valuable properties of individual components of serum, which lead to its use during the production of food products. Purification of milk whey from milk fat by separation. Separation of colloidal and ion-molecular systems of serum.
статья, добавлен 24.06.2024Characterization of elastic properties of saturated hydrocarbons and associates resinous-asfaltenovyh of compounds by simulating molecular dynamics. Evaluation of rheological behavior of heavy oil the elasticity matrix of transversely isotropic material.
статья, добавлен 27.07.2016Searching for cheap and effective corrosion protection methods. Research on the possibility of using "green inhibitors" as anti-corrosion measures. Characterization of the properties of the complex of inhibitors, alkaloids and tannins included in plants.
статья, добавлен 04.07.2022Character of force of friction is investigated and set in nominally-immobile connections on the stage of nominal adhesion and to passing to skidding. The capacity of connections are given by the method of coating on the basis of fusible to the alloy.
статья, добавлен 27.07.2021Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016Structure of engineering systems. A description of the statistical procedures recommended for use in reliability analysis "related" components. The choice of an appropriate probabilistic model for predicting the reliability of components of one's sibling.
статья, добавлен 14.09.2016An experimental study of backscattering factor for a linear accelerator Siemens Oncor Impression Plus for photon energies of 6 and 18 MV with asymmetric radiation fields. Development and implementation method for determining the backscattering factor.
статья, добавлен 29.07.2016Products of enzymatic hydrolysis of corn starch are promising multifunctional ingredients in yogurt, but their use requires studying influence on the vitality and activity of lactic acid bacteria, as well on some chemical characteristics of the product.
статья, добавлен 14.02.2025Methods of the equation of the cutting edge in the absolute coordinate system. A helix - a trace of movement of the cutting tool along the workpiece. Characteristics of the mathematical model of the formation of the microrelief surface when grinding.
статья, добавлен 06.05.2018Analysis of criteria for steels warping susceptibility under the thermochemical treatment. Study of value of the details warping during the quenching. Analysis of residual internal pressures in hardened layer and kinetics of austenitic grain growth.
статья, добавлен 30.01.2017The flexural and compressive strength of mortar by partial replacement of cement with Nano-ZnO particles has been studied. The results showed that the flexural and compressive strength of the cement mortars with ZnO were higher than pure cement mortar.
статья, добавлен 12.06.2018Proposes a method to increase information content in studying frequency properties of automatic control systems typical dynamic links based on representation of the link transfer functions in the form of graphs. Examples of separate links are provided.
статья, добавлен 25.01.2022Establishment of rational technological modes of processing various types of meat raw materials by needle injection on a multi-needle brine injector. Improvement of technologies and types of specialized equipment for injecting meat raw materials.
статья, добавлен 20.07.2024Improving matching techniques constructional and technological parameters of the installation with the modes of its work taking into account the features of the resonator. The changes in the dielectric parameters of raw material during the heat treatment.
автореферат, добавлен 30.04.2018- 117. Simplification and verification of dynamic equations of movement of an autonomous underwater vehicle
Autonomous underwater vehicles. The dynamic equations for describing the movement of a general AUV in a fluid with nonnegligible viscous properties and the possible simplification of this equation in regard to a specific construction of a real world AUV.
статья, добавлен 27.08.2020 Obtaining complex fertilizers by oxidation of Angren brown coal with a mixture of nitric and sulfuric acids and decomposition of oxidation products with a mineralized mass and slime phosphorite of the Central Kyzyl Kum. Fertilizers' commercial properties.
статья, добавлен 27.01.2021Scientific justification for automated control method of optimal charge of pebble mill operating in series with a magnetic separator in the second stage of crushing in magnetic separating plants that process on iron ores with varying physical properties.
статья, добавлен 23.03.2016Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019Solution of the problem of the theory of elasticity for a composite in the form of a half-space with a thick-walled round cylindrical tube and a layer rigidly attached to the surface of the half-space. Assessment of the stress state of the composite.
статья, добавлен 26.02.2021- 122. Finding the conditions of hydrocarbons safe storing and transportation in tanks of different shapes
Application of the software package ConvEx in the design of storage tanks for petroleum products prone to self-degradation. Investigation of the influence of the geometric shape of the vessel on the critical temperature of storage of petroleum products.
статья, добавлен 10.05.2018 Theoretical studies allow developing a theoretical substantiated method for calculating the stability of spray vortex countercurrent mass transfer device. Review and characterization of the effect on the drop centrifugal force and resistance forces.
статья, добавлен 14.07.2016Offered and analysed of the method of calculating the operating parameters of warping spools and mode of winding. A formula that is obtained allows to define relationship between the parameters of the threads wound on a warping spool and their pull.
статья, добавлен 29.11.2016The effect of mobile messaging during a conversation on impression formation and interaction quality computers. Cellular phone use in class: implications for teaching and learning: A pilot study. The effects of “phubbing” on social inter action.
статья, добавлен 20.01.2021