Residual Stress Measurements and Analysis by Destructive and Non Destructive Techniques
The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
Подобные документы
Описание характеристик DH и REDA процессов вакуумного обезуглероживания, развиваемых на заводе Nippon Steel. Тенденция снижения содержания углерода в ультранизкоуглеродистых сталях, ее минимальный достижимый уровень. Снижение предела процесса DH.
статья, добавлен 19.11.2018The relation between the particles velocity and the deposition efficiency of material powders. A different approaches for calculating the critical deposition velocity. Computational fluid dynamics model. Critical particle velocity determination.
статья, добавлен 29.11.2016The developing of the numerical model of viscoelastic material using finite element method. The comparison of the obtained results with use of FEM software with experimental data. The calculation of the stress and strain state of the asphalt specimen.
статья, добавлен 29.09.2016The study of magnetron sputtered coatings on base AlN-TiB2(TiSi2). The structural composition, morphology coated materials. Features amorphous-like coatings AlN-TiB2(TiSi2) after annealing and their impact on physical and mechanical properties changes.
статья, добавлен 30.07.2016Comparative analysis of the effect of chemical compounds on the process of forming an electric arc and the conditions for its combustion.Metal transfer in the interelectrode gap under experimental conditions. Specific power of electric arc discharge.
статья, добавлен 29.09.2016Consideration the mathematical model of process of pressing of seamless pipes. Effect on various forms of rolling shaping matrix. The nature of the formation of the deformation zone. Development of direct compression on a cylindrical mandrel pipe.
статья, добавлен 30.01.2016Improving matching techniques constructional and technological parameters of the installation with the modes of its work taking into account the features of the resonator. The changes in the dielectric parameters of raw material during the heat treatment.
автореферат, добавлен 30.04.2018Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
статья, добавлен 14.09.2016In this study, porous Ti-Nb-Zr biomaterial which is not included poison elements was successfully fabricated by powder metallurgy using space holder of NH4HCO3 and foaming agent of TiH2. Biocompatibility of porous Ti-Nb-Zr alloys is similar to Ti-6Al-4V.
статья, добавлен 30.07.2016Analysis of the use of aluminum alloys in the transport sector. Increased speed, safety, energy savings and reduced transport emissions thanks to aluminum. Ensuring a smooth ride and improved heat dissipation from the braking system using aluminum discs.
статья, добавлен 19.03.2024Іn this paper we present the microcontroller system for the diagnostics and evaluation of the Stirling engine performance. For this purpose the analysis model for the prototype engine has been developed to present the engine’s improved benchmarking result
статья, добавлен 29.07.2016Nanocomposites comprising ray in a polymer. The reflection mechanical properties material. Increasing the polymer properties by forming the interphase. Obtaining curves of stress-strain states of macroscopic samples irradiated polymer materials.
статья, добавлен 30.07.2016Square Lead-Rubber Bearings with four lead plugs to round Lead-Rubber Bearings with one lead plugs and shorten the analysis time. Comparison of load-deformation relationship. Comparison of the change in the outer edge temperature of the laminated rubber.
статья, добавлен 10.10.2021Розглянуто розроблення багатошарових захисних рідинних матеріалів для екранування електричних, магнітних та електромагнітних полів широкого частотного діапазону. Виготовлено серію рідких екрануючих сумішей на основі стандартних сертифікованих фарб.
статья, добавлен 31.01.2024- 40. Development of wide bandgap one-dimensional MOF/TIO2 photonic crystal and its gas-sensing properties
Metal-organic framework materials a type of coordination polymer that have seen breakthroughs in material science over the past decade. Because of their high specific surface area and porosity, they are used for gas adsorption, storage, and separation.
статья, добавлен 10.10.2024 Obtaining prototypes of hemp oil by cold pressing. Determination of mass fraction of moisture оil content measurement. Indicators of seeds' quality during long storage. Yield and quality indicators of by-products obtained in the production of hemp oil.
статья, добавлен 24.06.2022The present study is a mathematical modeling aimed at the dynamic force analysis of printed circuit boards in order to eliminate dynamic stresses to an acceptable level and ensure the strength and reliability of the printed circuit board design.
статья, добавлен 02.06.2022- 43. Global Research on Artificial Intelligence from 1990–2014: Spatially-Explicit Bibliometric Analysis
The evaluation of artificial intelligence research from 1990–2014 by using bibliometric analysis. Growth trend of articles in artificial intelligence from. Temporal pattern of frequently used keywords. International Productivity and Collaboration.
статья, добавлен 02.02.2017 Impact indicators coal shiites in the properties of the resulting coke. Coking process with the help of passive experiment. Effect of changes in the number of components of the coal charge on the quality of the coke at various technologies of sintering.
статья, добавлен 29.07.2016Increase in the use of hard, high strength and temperature resistant materials in engineering necessitated the development of machining techniques. Abrasive flow machining as process non-conventional machining processes. Magneto abrasive flow machining.
статья, добавлен 02.06.2014А technology for manufacturing composite materials - flocculants-coagulants on aluminum-silicon and iron-silicon base. The evaluation of the effectiveness of the developed flocculants-coagulants for cleaning of natural water and industrial wastewater.
статья, добавлен 11.01.2018Analysis of the aspects of the specifications and drawings of plastics that are specific to this family of materials and processes and that are related to the realities that need to be taken into account. Cavity identification and rough indication.
статья, добавлен 10.03.2019- 48. Principles of calculation of piezoelectric elements with surfaces partial covering by electrodes
Description of stress-strain state and transfer characteristics of piezoelectric elements with partial surfaces electrogalvanism. The power method of the analysis of the physical condition of the piezoelectric elements in the mode of forced oscillations.
статья, добавлен 30.08.2016 The main production methods jet fuels rocket engines. Prospects for the use of various raw materials to produce jet fuels in the context of limited energy resources. The impact of processing production and use of aviation fuels on the environment.
статья, добавлен 23.02.2016Test the tribological properties of lubricants as the main stage of assessing their suitability for use in friction. The scheme of the "cone - three ball" with the use of objects of simple geometric shapes to test different construction materials.
статья, добавлен 29.01.2016