Residual Stress Measurements and Analysis by Destructive and Non Destructive Techniques
The investigation is focused on the evaluation of residual stresses resulting from cold deformation and welding in candidate target structural materials such as martensitic Alloys EP-823 and HT-9, and also an austenitic Type 304L stainless steel.
Подобные документы
The regularities of macromolecules behavior in the flow with longitudinal velocity gradient and manifested in this case effects of elastic deformations have importance in understanding the mechanism of anomalously high cutting power of water-polymer jet.
статья, добавлен 28.02.2016The scientific article provides a botanical description of the species Rosmarinus officinalis L. Information is provided on the extraction of essential oil and the use of the resulting essential oil in medicine, cosmetology, aromatherapy and cooking.
статья, добавлен 26.02.2025Presents various methods of piling, using undercutting, as well as various combinations of these methods. The impact load on the pile head is created by special mechanisms. Driving piles by screwing is based on driving steel and reinforced concrete.
статья, добавлен 10.10.2024Анализ рынка бесшовных труб из низколегированных сталей в Казахстане и макрорегионе. Совершенствование технологии выплавки стали для повышения её стойкости к водородному растрескиванию. Определение себестоимости стали по предлагаемой технологии.
диссертация, добавлен 20.03.2017Processes of change of mechanical properties and microtexture of castings from gazars. Effect of monolithic areas formation inside the porous structure. Consideration of monolithic formations inside porous structure of gazar after annealing, x 50.
статья, добавлен 30.01.2016Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016The roller of the belt as the most important parts of the conveyor, being subjected to continuous stress both during operation and in stopping periods. Causes and weight percentage of failures due to fatigue. Sealing system with simple labyrinth.
статья, добавлен 27.12.2016Transit of natural gas along the territory of Ukraine to the countries of the Western and Central Europe. Main resons of the loss of pipeline efficiency. Necessity for studying of the operation modes of the gas transport system during underloading.
статья, добавлен 01.12.2017Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Properties and structure of hydrocarbons. Types and communication aromatics. The nature of the relationship between the carbon atoms. The methods of extraction and processing of oil. The use of the rectification columns for fractionating of raw materials.
презентация, добавлен 30.06.2014Improving the physical and mechanical properties of powder steels. Study of the effect of heat treatment on the structure of powder carbon steels with carbon-containing components. Research of heat treatment processes: hardening, tempering and annealing.
статья, добавлен 27.02.2021Analysis of finite element methods, numerical methods for solving engineering and mathematical physics. Obtaining analytical solutions for problems of complex geometry, loads and material properties. Tension rods, beams and other simple structures.
презентация, добавлен 20.10.2014Consideration and characteristics of the scheme double-point wheel-rail interaction. Familiarization with the erosive wearing. Definition of the dependence of the coefficient of adhesion on the temperature. Analysis of sand system of the locomotive.
статья, добавлен 26.09.2016The mixed approach that combines theoretical research, analysis of scientific research with analysis of practical examples, increasing visitor engagement through augmented reality, virtual reality technologies, also encompasses important design aspects.
статья, добавлен 24.06.2024Creation and testing of a model of a diesel engine muffler. Plotting a pressure level diagram inside the device. Analysis of the distribution of the sound field. Assessment energy losses of exhaust gases. Estimation of the spectrum and octave bandwidth.
статья, добавлен 10.10.2024Familiarity with the basic method of identification of defects of the drive with induction motor using wavelet transform for the test signals. Analysis of a neural network model converted to the next subsequent stages on the basis of the algorithm.
статья, добавлен 28.08.2016Structure of engineering systems. A description of the statistical procedures recommended for use in reliability analysis "related" components. The choice of an appropriate probabilistic model for predicting the reliability of components of one's sibling.
статья, добавлен 14.09.2016The system of rest is energy-saving, with power supply from alternative energy sources intended for complex recovery of an organism in house conditions. Determine the effectiveness of panel modules on the level of stress. Application panel "Ananta 2016".
статья, добавлен 19.12.2017Integrating lignin with synthetic plastics - an innovative approach in the development of sustainable polymers. Nanofibers with antimicrobial properties - one of the innovative materials that can be effectively used in the current pandemic situation.
статья, добавлен 13.04.2022Theoretical study of the basic functioning of the starch industry. The raw materials used for the а production of polysaccharide under consideration. The structure of the modified starches and dextrin. The use of the ingredient as a food additive.
презентация, добавлен 27.10.2014Development of flexible-wing Micro Air Vehicles at the University of Florida. Design intent and approach, identifying airplane components, fabrication techniques and various testing methods used to assess overall airplane and component performance.
статья, добавлен 18.01.2014The surfactants have been objects of studies all over the world. Development of approach to surfactants with controllable structure and properties based on the natural raw materials applicable for cosmetics production as dispersed systems stabilizers.
статья, добавлен 23.09.2016The paper presents the design of experimental cells, a description of materials for construction and construction process, and preliminary results. The objective of the work is proving which of the MBT fractions function better for methane degradation.
статья, добавлен 08.10.2020A modern house built using materials that "smell of the past, but strive for the future." The use of mechanical ventilation with dehumidification, radiant floor, photovoltaic panels with energy storage and heat pump. Creating a comfortable temperature.
статья, добавлен 04.10.2021Hydrothermal sol-gel synthesis of hexagonally ordered silicas using a hybrid template system is reported. Silicas were characterized by IR spectroscopy, X-ray diffraction techniques as well as electron microscopy. The hexagonal structure of MCM-41.
статья, добавлен 30.07.2016