History of a petroleum industry of the second half XIX and the XX-th century beginnings as a source for a museum collection
Gathering of materials about a petroleum industry in a museum creates favorable conditions for their protection. The assemblage of materials is stored In a museum about the factory "Brothers Nobel". The oil extracted by brothers Nobel in 1894-1903.
Подобные документы
Mechanical tests of with various hydrogen concentrations before and after the hydride reorientation tests were performed. Hydrogen pickup measurements in zirconium alloys: relation to oxidation kinetics. Hydride microstructure in the dummy claddings.
статья, добавлен 30.05.2021Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016- 103. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 Study of problems the sufficient conditions for the existence of solutions of linear nonhomogeneous impulsive boundary value problems with small perturbations when generating boundary value problem of impulsive has solutions for arbitrary right-hand side.
статья, добавлен 30.01.2017The history of iron and Damascus steels through the eyes of ancient blacksmiths. Observation of color changes during heating and estimating of hardness by scratch tests, to have determined some key parts of the present-day iron-carbon phase diagram.
статья, добавлен 09.09.2012The system of rest is energy-saving, with power supply from alternative energy sources intended for complex recovery of an organism in house conditions. Determine the effectiveness of panel modules on the level of stress. Application panel "Ananta 2016".
статья, добавлен 19.12.2017Experimental researches of improvement of technology of preparation of preparation Torasemide 5 mg / ml a solution for injections, a choice of a filtering material. Aseptic production conditions using sterile filtration and thermal sterilization.
статья, добавлен 01.12.2017The relationship between the research of technology and sound. The history of the creation of the first electronic music synthesizer. Standardization of the keyboard, the role of users of technology. Sound creation technologies, performance practices.
статья, добавлен 21.11.2021Rheology of high-viscosity marine fuel, temperature conditions of fuel preparation in ship power plant. The relationship between objects, environment and fuel quality of the fuel spray. Influence of variable electric fields for high-viscosity marine fuel.
статья, добавлен 28.09.2016- 110. The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
статья, добавлен 29.01.2016 Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
статья, добавлен 21.12.2016Investigation of the surface layer structure at high resolution. Study of surface morphology of treated detail. The use of electric-surface alloying components operating under conditions of friction and abrasionerosion wear and their restoration.
статья, добавлен 22.03.2016Problems of hardware configuration in systems for stabilization of information and measuring devices operated at vehicles of wide class in difficult conditions of disturbances action. Analysis of modern devices and units used in stabilization systems.
статья, добавлен 14.09.2016The conductive nanocomposite films based on functional reactive copolymers and bifunctional alcohols. Creation multiwall carbon nanotubes. Dependence properties of the nanocomposites from the specific composite composition and obtaining conditions.
статья, добавлен 30.07.2016Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016Study of field distribution in structures such as a gold lattice, a graphene layer, and a silicon substrate. Conditions of maximum electromagnetic field distribution by these structures for the purpose of using them in photonics and electronics devices.
статья, добавлен 24.02.2024Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016