Machining on a grinding machine
Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
Подобные документы
Consideration of the problems of energy conservation and management of production costs at metallurgical enterprises. The necessity of carrying out an energy-resource-saving policy of metal producers has been substantiated; directions of energy saving.
статья, добавлен 30.09.2021The study of structural changes during hot deformation metal during controlled rolling. The influence of preheating temperature and deformation degree on the size and shape of austenite grains. The definition of the polygonal structure of the austenite.
статья, добавлен 30.01.2017Rational modes of printing volumetric samples with a working thickness of the 316L powder layer of 40 μm to achieve a density of volumetric samples/ Determination of the density of metal samples by the metallographic method on an optical microscope.
статья, добавлен 19.03.2024Structure of engineering systems. A description of the statistical procedures recommended for use in reliability analysis "related" components. The choice of an appropriate probabilistic model for predicting the reliability of components of one's sibling.
статья, добавлен 14.09.2016Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Analysis of design features and parameters of automobile and aircraft engines is carried out. It is shown that car engines, despite the high technical level achieved at the beginning of the 21st century, do not technically meet aviation requirements.
статья, добавлен 19.06.2022The comparative analysis of the microstructure, phase and chemical composition of the experimental alloys of the Fe-W type with the standardized grade ferrotungsten. The feasibility of using Fe-W for the manufacture high tungsten materials based on iron.
статья, добавлен 30.01.2016The study of the influence of the surface hardness of the auger on its wear during dehydration of solid waste in the garbage truck. Usage of the method of regression analysis, the logarithmic dependencies of auger wear depending on the hardness.
статья, добавлен 23.06.2022Determination of the design principles of shaping in the design of fur garments that provide innovative character of the design activities and high level of artistic and stylistic properties of the projected objects. Principles of composition for design.
статья, добавлен 31.05.2022The use of the boundary values of parameters of mould displacement of the earth's surface and refining the workings of the design scheme to predict the trajectory of sedimentation. Determination of empirical coefficients of mathematical equations.
статья, добавлен 30.07.2016Events held before the loading and unloading of heavy cargo, including taking into account the fact that the ship has an initial roll angle. The position of the keel when loading. The main criteria of ship stability during heavy lift operations.
статья, добавлен 28.09.2016Using and improvement of qualities of products of oil processing. The process of obtain a water-soluble colloidal sulfur with seating stability, good solubility in water, high biological activity. Selection of conditions to receiving polymeric products.
статья, добавлен 11.03.2019Analysis of the overall stiffness range of most plastics in combination with common efforts to use the thinnest wall thickness possible. Dependence of plastics processing processes on tool quality and process parameters. Basic design considerations.
статья, добавлен 10.03.2019Features of the application of methods for monitoring the state of the wooden structure in the production flow. Ways to optimize the prediction of wood properties using various NDE methods. The combination of methods for effective quality control of wood.
статья, добавлен 29.11.2018Evaluation of the technical system and its subsequent use for decision-making to ensure complex technical systems with appropriate quality of work. The characteristics and specificity of the model changes performance States based on the Markov chain.
статья, добавлен 29.01.2016Learning algorithm of consistent actions to obtain quality coatings made by the complex technological method electrocontact strengthening of sprayed coatings. Analysis Ishikawa diagram which allows identify the causes of the impairment coatings obtained.
статья, добавлен 29.01.2016Development of the composition of water-epoxy coating NIPU. Study the compatibility of components in water-based coatings. The optimum ratio of the components of the composition to obtain the necessary physical and mechanical properties of the coating.
статья, добавлен 29.07.2017Using transmission electron microscopy methods the layer by layer analysis of the bulk hardened superior quality rails is carried out, phase state and defect substructure gradients are established. Character of changing of structure-phase states.
статья, добавлен 30.07.2016Obtaining prototypes of hemp oil by cold pressing. Determination of mass fraction of moisture оil content measurement. Indicators of seeds' quality during long storage. Yield and quality indicators of by-products obtained in the production of hemp oil.
статья, добавлен 24.06.20223D printing (Additive Manufacturing Process, AM) is any of various processes used to make a three-dimensional object without the use of dies, molds or machining. The most basic, differentiating principle behind 3D printing. General principle modeling.
статья, добавлен 20.02.2019Super ultrahard nanostructured and nanocomposite thin films. Preparation and industrial applications of hard and superhard nano-structured coatings on tools for machining (drilling, milling, turning), forming, stamping, injection moulding and the like.
статья, добавлен 30.07.2016Transit of natural gas along the territory of Ukraine to the countries of the Western and Central Europe. Main resons of the loss of pipeline efficiency. Necessity for studying of the operation modes of the gas transport system during underloading.
статья, добавлен 01.12.2017Test the tribological properties of lubricants as the main stage of assessing their suitability for use in friction. The scheme of the "cone - three ball" with the use of objects of simple geometric shapes to test different construction materials.
статья, добавлен 29.01.2016Study the structure of the coating made of composite material that contains wear-resistant components SiC-Al2O3. The use of a metallic binder based on iron in composite production. The properties of the obtained coatings with the steel counterface.
статья, добавлен 29.01.2016Improving the physical and mechanical properties of powder steels. Study of the effect of heat treatment on the structure of powder carbon steels with carbon-containing components. Research of heat treatment processes: hardening, tempering and annealing.
статья, добавлен 27.02.2021