Machining on a grinding machine
Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
Подобные документы
The influence of the addition of soy flour processed by ultrafine grinding and irradiation on the quality of crispy baked goods. The wet soybean grounds were dried and ground in an ultra-fine grinding machine. Also set the ratio of beans to water.
статья, добавлен 02.06.2022Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016Grinding of loose materials in order to increase the contact surface, improving rheological activity for the intensification of a number of chemical and physical. Select the most efficient and economically viable method of grinding a hard material.
статья, добавлен 14.03.2019Appointment, device and action of the turning machine. Types of lathes, depending on the application. Metal processing on machine tools, turning operations. The use of water energy to drive. The principle of operation of the hydroelectric station.
статья, добавлен 11.03.2019Methods of the equation of the cutting edge in the absolute coordinate system. A helix - a trace of movement of the cutting tool along the workpiece. Characteristics of the mathematical model of the formation of the microrelief surface when grinding.
статья, добавлен 06.05.2018The analysis of the cement production process in Ghana, which is limited to grinding clinker into cement and its packaging and distribution. The equipment of grinding chains, the best configuration. Control methods used for cement grinding chains.
статья, добавлен 30.05.2018The methodical approach that is aimed at the efficient use of existing fixed assets and technological innovations introduction. Technical and technological components of the technological machine-building enterprise "Turbomash Ltd" development.
статья, добавлен 26.08.2016Increase in the use of hard, high strength and temperature resistant materials in engineering necessitated the development of machining techniques. Abrasive flow machining as process non-conventional machining processes. Magneto abrasive flow machining.
статья, добавлен 02.06.2014Comparison of two non-conventional processes which are laser and photochemical machining. The formation of complex shapes in metal sheets. Chemical etching of the material for the manufacture of the desired finished product by a controlled corrosion.
статья, добавлен 03.12.2015Characteristics of mathematical model of dynamic processes that occur in frictional hardening of flat surfaces of machine parts with use of the tool with the cut transverse grooves on its working parts. Cyclic circuit of the machine’s oscillations.
статья, добавлен 14.09.2016The control station is designed for the control and smooth adjustment of the rotation frequency of the shaft of the alternating current electric motor depending on the operating characteristics of the technological equipment of the rod depth pump units.
статья, добавлен 10.12.2024- 12. Development of wide bandgap one-dimensional MOF/TIO2 photonic crystal and its gas-sensing properties
Metal-organic framework materials a type of coordination polymer that have seen breakthroughs in material science over the past decade. Because of their high specific surface area and porosity, they are used for gas adsorption, storage, and separation.
статья, добавлен 10.10.2024 Directions of development of production technology of high-precision parts. Research in the field of management precision and quality parameters of the treated surface. Improvement of the technological process, equipment, instruments and devices.
статья, добавлен 06.12.2016Experimental improvement of the stability of the bolt connection of the technological and power modules of the new design of the modular machine-tractor unit. The new construction of the pivot connection of the technological module with the power module.
статья, добавлен 10.08.2022Investigation of the surface layer structure at high resolution. Study of surface morphology of treated detail. The use of electric-surface alloying components operating under conditions of friction and abrasionerosion wear and their restoration.
статья, добавлен 22.03.2016Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016General characteristics of the hydrostatic spindle for ultraprecision double-sided machining. Familiarity with the main features and problems of modern engineering development. Consideration of ways to ensure quality indicators of machining parts.
статья, добавлен 20.07.2020Volumes of agricultural production of whole grain rice in Kazakhstan. Development of a technology for improving peeler for processing grain rice shals. Characteristics of polymeric materials used instead of rubber for rollers shelling machine A1-3RD-3.
реферат, добавлен 16.10.2017Motion systems as core technologies, as mechanical systems, like microelectronic manufacturing equipment, are required to achieve high speed and accuracy. The influence of the dynamics of a mechanical system on the quality of the position tracking syste
статья, добавлен 26.08.2020Intensive deformation of the elastic system of the machine - specific features of the cutting process. Circumcision of the gear with a disk the cutter in the continuous circular movement of the pinion - essence of the radial-circular cutting mode.
статья, добавлен 14.09.2016In the article, high-temperature superconductivity is investigated and studied, and its promising paths are shown. One of these methods is the application of extreme pressures. In addition to hydrogen-containing materials, the article reflects the names.
статья, добавлен 10.10.2024Studies on the preparation of pasty high-filled compositions and evaluation of their rheological properties using a rotational visco-meter "Reotest-2" on the cone-plane system. Evaluation of sedimentation resistance of compositions and their flow.
статья, добавлен 30.10.2016Defining of dimensional relationships where the aspect ratio. The building process for 3D microdevices. The features of creation surface energy high enough to maintain adhesion of the electroplated material until completion of the plating process.
реферат, добавлен 16.04.2017Rheology of high-viscosity marine fuel, temperature conditions of fuel preparation in ship power plant. The relationship between objects, environment and fuel quality of the fuel spray. Influence of variable electric fields for high-viscosity marine fuel.
статья, добавлен 28.09.2016