A VTOL Micro Air Vehicle Design Concept and Projected Mission Utility
Design, develop Micro Air vehicle system provides a platform to support a very wide variety of missions for the small unit. Further miniaturization of electronics and sensors these vehicles to become even smaller and to operate in complex environments.
Подобные документы
The use of the boundary values of parameters of mould displacement of the earth's surface and refining the workings of the design scheme to predict the trajectory of sedimentation. Determination of empirical coefficients of mathematical equations.
статья, добавлен 30.07.2016- 52. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 Service robot - device which used for cutting the grass or vacuum cleaning. Repairing of damaged inner pipe wall. Substituted human in dangerous or monotonous works via using of robots. Cleaning brush module for dirties removing. Design of tracked robot.
статья, добавлен 28.08.2020- 54. Complex of activation tools for energy saving measures in housing and utilities sector of the city
Regulatory basis that promotes the development of renewable energy in Ukraine. The features of energy saving measures as a complex final consumption product. A complex of activation instruments being adjusted to the characteristics of individual objects.
статья, добавлен 24.02.2016 Analyze existing installations for fire testing of building constructions both in Ukraine and abroad. Design a model of fire furnace was. Determination of the fire resistance of different constructive systems. Implementation of models of fire furnаces.
статья, добавлен 24.02.2016An overview of the current trend in the development, production and application of efficient biodegradable polymer materials and composites. Ways of hybrid modification of biodegradable polymeric composite for obtaining effective products based on them.
статья, добавлен 24.09.2023The present study is a mathematical modeling aimed at the dynamic force analysis of printed circuit boards in order to eliminate dynamic stresses to an acceptable level and ensure the strength and reliability of the printed circuit board design.
статья, добавлен 02.06.2022- 58. Investigation of properties of the constant technological track, which is used in bridge agriculture
Mechanical properties of soil traces of a permanent technological track and their influence on the traction and traction properties of a bridge agricultural machine of a new design. The research was conducted using the provisions of the tractor theory.
статья, добавлен 30.08.2022 Study of field distribution in structures such as a gold lattice, a graphene layer, and a silicon substrate. Conditions of maximum electromagnetic field distribution by these structures for the purpose of using them in photonics and electronics devices.
статья, добавлен 24.02.2024The model of spatially distributed curing process of epoxy matrix polymeric composite. The model using the projections of Pareto points set on the 8-dimensional space of design variables. Сontrol synthesis for the closed mould curing of composite spar.
статья, добавлен 30.05.2017Fast fatigue crack growth. The general content of nitrogen in the alloy system that limits fatigue life. Fragmenting the titanium sponge into small pieces and using various melting methods metals. Investigation of the Partially Melted Electrodes.
статья, добавлен 10.12.2018Analysis of the artistic and compositional characteristics of Ukrainian traditional embroidery and other works of decorative and applied art for decorating current clothing models in ethnostylistics. Designing author's models of modern clothing.
статья, добавлен 05.04.2023Analysis and comparison of the different rotor type permanent magnet machines. The presented machines are designed as having same geometrical dimensions and same materials for comparison. Permanent magnet machines, mathematical modeling, motor geometry.
реферат, добавлен 25.03.2011Development of a managed system architecture with the possibility of full-scale parametric optimization. Systematization of the architecture of the conversion system by the example of the technological process of liquid heating. Software designer EFFLI.
статья, добавлен 30.10.2016Analysis of requirements for electric-drive of mechanism of pulsed wire feed, and the benefits of using a special Brushless Direct Current electric-drive. Design of half-bridge circuit to regulate the strength of the current phase of the stator windings.
статья, добавлен 22.12.2016Two sensor designs of metallic cylindrical resonator Coriolis vibratory gyroscope are analyzed in this work. Resonant frequencies computer modeling results are resented and on their basis gyroscope sensor geometrical parameters choice is validated.
статья, добавлен 14.09.2016The problem of fuzzy multicriterial analysis of local energy conversion systems. Construction of training samples for artificial neural networks. Application of multiagent calculating models. Transition from vectorial criterion to a scalar combination.
статья, добавлен 28.08.2016The base of constructing computer model of the analysis of complex physical-chemical phenomena in the process ORIEN in continuous arc furnace is as the main aggregate of energy-metallurgical complex. A mathematical model of physical-chemical processes.
статья, добавлен 02.11.2018Modernization of the transport system of the production system MPS 500. Creation of a new control program in the environment of the TIA portal. The main functions of the frequency converter. Investigation of the final state of the control cabinet.
статья, добавлен 26.08.2020The study of the formation mechanism of flavonoid complex with aluminum ions. On the basis of the negative low Gibbs free energy values it found that chelation is a natural phenomenon. Determination of the antioxidant capacity of flavonoids stevia leaf.
статья, добавлен 30.01.2016Comparison of two non-conventional processes which are laser and photochemical machining. The formation of complex shapes in metal sheets. Chemical etching of the material for the manufacture of the desired finished product by a controlled corrosion.
статья, добавлен 03.12.2015Obtaining complex fertilizers by oxidation of Angren brown coal with a mixture of nitric and sulfuric acids and decomposition of oxidation products with a mineralized mass and slime phosphorite of the Central Kyzyl Kum. Fertilizers' commercial properties.
статья, добавлен 27.01.2021Evaluation of the relevance of Vernadskyi's noosphere concept. Transformation of the biosphere by man with the help of the mind. Development in the direction of the creation of technical subjects and replacement of the biosphere with the technosphere.
статья, добавлен 18.04.2023The peculiarity of the formation and development of the system of ensuring the unity of measurements in Ukraine, in particular its technical basis - the reference base. Stages of formation of the Ukrainian system of ensuring the unity of measurements.
статья, добавлен 26.03.2023The adapted pitch concept involves varying the pitch and the length of the cutting portion as a function of the taper of the instruments. HEROShapers used to prepare and enlarge the coronal and middle thirds of the canal. The removal of dentinal chips.
статья, добавлен 10.12.2013