A VTOL Micro Air Vehicle Design Concept and Projected Mission Utility
Design, develop Micro Air vehicle system provides a platform to support a very wide variety of missions for the small unit. Further miniaturization of electronics and sensors these vehicles to become even smaller and to operate in complex environments.
Подобные документы
The surfactants have been objects of studies all over the world. Development of approach to surfactants with controllable structure and properties based on the natural raw materials applicable for cosmetics production as dispersed systems stabilizers.
статья, добавлен 23.09.2016The obstacle in the way of nanotechnologies is the lack of selective "scalpel and forceps", the instruments to operate with particles of size less than 10-9 meters, particularly with molecules and atoms. Atomic forceps and scalpel for nanotechnologies.
статья, добавлен 29.12.2023The place of interdisciplinary educational technology in the system of engineering training. The role of the course of theoretical mechanics in the system of engineering disciplines. Presentation of scientific and subject knowledge of the discipline.
статья, добавлен 12.08.2020The risk-creating factors of the projects of creating samples of unmanned aviation equipment were determined. An approach to risk assessment at various stages of research and development works on the development of unmanned vehicles is proposed.
статья, добавлен 13.07.2022Environmental biotechnology study the use of living organisms for a wide range of applications in hazardous waste treatment and pollution control. The use of biotechnology in the dairy industry. Methods for producing whey. Security staff activity.
курсовая работа, добавлен 13.04.2015Іn this paper we present the microcontroller system for the diagnostics and evaluation of the Stirling engine performance. For this purpose the analysis model for the prototype engine has been developed to present the engine’s improved benchmarking result
статья, добавлен 29.07.2016Special supervisory control system responsible for the informative data acquisition about the current enterprise production and its control. The main SCADA. The general structure of SCADA. The Three main structure components modern SCADA-systems.
статья, добавлен 30.04.2019Characteristics of an automated traffic management system based on the use of neural networks. Description of the mathematical model of the intersection. The strategy of motion control using a neurocontroller, based on the multilayer perceptron.
статья, добавлен 22.12.2016Research of mathematical model of the process intrusion forming polymer products. Establishing a dependency on the angle of melt costs lifting screw injection unit in the material cylinder based on the geometric parameters of extrusion head and mold.
статья, добавлен 18.02.2016Tissue Paper and its properties. Space and weight characteristics. Carrier and type of aircraft for transportation. Limitations by sizes, weight and loading on the floor. Calculation of number of bags that we can put into one box. Manipulation signs.
курсовая работа, добавлен 16.12.2013System for billet continuous caster’s mould heat engineering parameters monitoring. Formation of the internal heat transfer surfaces. Calculation the indicators: average heat flux density, overall heat exchange coefficient. Effective gas gap thickness.
статья, добавлен 30.01.2016Strength is assumed - index for materials which can take standard, calculated values. Significant dependence between bending resistance, absolute size of structural elements. The structure of the wood fibers - factor which determine timber quality.
статья, добавлен 25.12.2016There exists a wide range and a considerable potential of alternative gas fuel types. Uncertainty, flexibility of nonconventional fuels’ composition seriously limits the possible exploitation of these energy sources. Equations of chemical thermodynamics.
статья, добавлен 30.07.2016Analysis of the main causes of destruction of adhesive joints. Structural and technological stress concentrators, because of which cracks develop during operation. General characteristics of the resistance of adhesive bonding to failure at all stages.
статья, добавлен 30.04.2018Experimental heat treatment of coal from the Shoptykol deposit of the Maikuben basin by carbonization, activation in a pilot laboratory unit. Analysis of the adsorption characteristics of the samples. Approbation of the obtained activated carbon.
статья, добавлен 28.12.2020Results of research for increase in an output of target paraffins during of deparaffinisation mineral oil are resulted by a spirit-water solution of a carbamide. The variant removal of paraffins which output normal alkanes from the potential maintenance.
статья, добавлен 10.08.2018Production polystyrene composite films with small content of fullerenes (up to 1 %) by casting o-xylene solutions. A dependence of the glass transition temperature of the composite material on its composition. The adsorption capacity of polymer material.
статья, добавлен 30.07.2016Character of force of friction is investigated and set in nominally-immobile connections on the stage of nominal adhesion and to passing to skidding. The capacity of connections are given by the method of coating on the basis of fusible to the alloy.
статья, добавлен 27.07.2021The main advantages and disadvantages of well-known spiral drills with a multi-stage blade. It is described that the bridge, together with the steps adjacent to the grooves, is a small centering drill, performs centering and drilling during the process.
статья, добавлен 10.02.2021Peculiarities of application of mathematical apparatus for the calculation of point Baluba-Naidysh to develop the technology for scanning of the light openings of different configurations. Method of determining point equations for parabolic window.
статья, добавлен 07.12.2016Study of problems the sufficient conditions for the existence of solutions of linear nonhomogeneous impulsive boundary value problems with small perturbations when generating boundary value problem of impulsive has solutions for arbitrary right-hand side.
статья, добавлен 30.01.2017Structure of three-cone rock bit with inserted hard-alloyed rock-destruction and protecting equipment, in which the chief components are marked. The minimally possible set of operators, which support qualitative performance of technological process.
статья, добавлен 14.09.2016The main factors of physical phenomena that accompany the process of power explosive effect for the development of new processes of metal processing. Industrial testing of facing technology by explosion of artificial surfaces of complex configuration.
статья, добавлен 19.02.2019Consideration the processes taking place in the metal pipe during prolonged use. Studing the complex physical and mechanical properties to assess the resistance to the destruction of the metal in the environment closest to the operating conditions.
статья, добавлен 30.01.2016Analysis of finite element methods, numerical methods for solving engineering and mathematical physics. Obtaining analytical solutions for problems of complex geometry, loads and material properties. Tension rods, beams and other simple structures.
презентация, добавлен 20.10.2014