Improved methodology for calculating the processes of surface anodic dissolution of spark eroded recast layer at electrochemical machining with wire electrode
Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
Подобные документы
There exists a wide range and a considerable potential of alternative gas fuel types. Uncertainty, flexibility of nonconventional fuels’ composition seriously limits the possible exploitation of these energy sources. Equations of chemical thermodynamics.
статья, добавлен 30.07.2016The analysis of the cement production process in Ghana, which is limited to grinding clinker into cement and its packaging and distribution. The equipment of grinding chains, the best configuration. Control methods used for cement grinding chains.
статья, добавлен 30.05.2018Model for calculation of nominal stresses in characteristic points of the surface fatigue crack to the tubular shaft in bending with rotation. Reasons for the decrease of the propagation velocity of cracks in the center and changing the geometry.
статья, добавлен 28.09.2016The main criteria for the quality of a pile coating, obtained by electro-floating. Experimental data obtained on a sample of nylon pile used in applying pile coatings by electro-floating method, which prove the efficiency of the proposed method.
статья, добавлен 30.08.2020Determining the effect of coating thickness on Hardness which is used on the protective layer when polyester coating is applied on the aluminum coil. Determining the scratch hardness using Hardness pencils test according to Wolff-Willborn "ASTM D3363".
статья, добавлен 06.05.2018Analysis of requirements for electric-drive of mechanism of pulsed wire feed, and the benefits of using a special Brushless Direct Current electric-drive. Design of half-bridge circuit to regulate the strength of the current phase of the stator windings.
статья, добавлен 22.12.2016Study the structure of the coating made of composite material that contains wear-resistant components SiC-Al2O3. The use of a metallic binder based on iron in composite production. The properties of the obtained coatings with the steel counterface.
статья, добавлен 29.01.2016The conductive nanocomposite films on the basis of reactionary copolymers received. The threshold of their percolation is determined. It was shown that its value depends on the size of specific surface of nanotubes and conditions of composite obtaining.
статья, добавлен 23.09.2016Consideration an alternative, in relation to the widely used "differential" one, "integrated" approach to solving the dynamics problems. Determining the natural frequencies of fluctuations case of the free surface liquid in containers of various shapes.
статья, добавлен 29.11.2016Analysis of the existing methods of the automatic regulation of the process of the drying of timber. Algorithm of the regulator of kiln drier. The need of regulating the drying process taking into account the characteristics of wood and drying agent.
статья, добавлен 28.11.2016A new concept of Artificial Neural Networks in estimating speed and controlling a separately excited DC motor. A three-layer feed forward neural network with sigmoid activation functions in the input and hidden layers and purelin in the output layer.
статья, добавлен 22.08.2017Development and value of a robotic module, whose activity will be controlled based on the perception of the image obtained from a digital camera. Features and description of the process of creating an intelligent robotic module with a camera system.
статья, добавлен 28.08.2020Proposal and implementation of a new methodology for calculating the bending finned tubes for heat exchange systems. Getting high-quality bends with minimum radius of bending pipes bimetallic and monometallic. The use of technology in the helical rolling.
статья, добавлен 24.02.2016Character of force of friction is investigated and set in nominally-immobile connections on the stage of nominal adhesion and to passing to skidding. The capacity of connections are given by the method of coating on the basis of fusible to the alloy.
статья, добавлен 27.07.2021Studies of Heat and Mass of drying in the process for the production of slag gravel. Determination of the temperature of the thermal agent at the height of the layer of materials. The dependence of the velocity of the mass transfer of temperature zones.
статья, добавлен 24.02.2016- 41. Development of wide bandgap one-dimensional MOF/TIO2 photonic crystal and its gas-sensing properties
Metal-organic framework materials a type of coordination polymer that have seen breakthroughs in material science over the past decade. Because of their high specific surface area and porosity, they are used for gas adsorption, storage, and separation.
статья, добавлен 10.10.2024 Comparative analysis of the effect of chemical compounds on the process of forming an electric arc and the conditions for its combustion.Metal transfer in the interelectrode gap under experimental conditions. Specific power of electric arc discharge.
статья, добавлен 29.09.2016Super ultrahard nanostructured and nanocomposite thin films. Preparation and industrial applications of hard and superhard nano-structured coatings on tools for machining (drilling, milling, turning), forming, stamping, injection moulding and the like.
статья, добавлен 30.07.2016Comparison of the results of processing arrays light absorption alternate method of incorporating calibration surface with other methods. Determination of Ni2 +, Co3 +, Fe2 +, Cu2 + from 1-(2-pyridylazo)-2-naphthol in aqueous-micellar environment.
статья, добавлен 23.02.2016Analysis of the effect of deposition parameters on the crystal structure, surface morphology and compositional properties of an indium sulfide films. The use of electron microscopy to study the orientation of grains. Investigation of optical absorption.
статья, добавлен 21.12.2016Using transmission electron microscopy methods the layer by layer analysis of the bulk hardened superior quality rails is carried out, phase state and defect substructure gradients are established. Character of changing of structure-phase states.
статья, добавлен 30.07.2016Peculiarities of application of mathematical apparatus for the calculation of point Baluba-Naidysh to develop the technology for scanning of the light openings of different configurations. Method of determining point equations for parabolic window.
статья, добавлен 07.12.2016Presents various methods of piling, using undercutting, as well as various combinations of these methods. The impact load on the pile head is created by special mechanisms. Driving piles by screwing is based on driving steel and reinforced concrete.
статья, добавлен 10.10.2024Research of influence of the electric discharge machining on change the properties of water. The formation of free radicals and hydrogen peroxide under the influence of cavitation is established, which leads to an increase in the whiteness of the wool.
статья, добавлен 21.12.2016Rational modes of printing volumetric samples with a working thickness of the 316L powder layer of 40 μm to achieve a density of volumetric samples/ Determination of the density of metal samples by the metallographic method on an optical microscope.
статья, добавлен 19.03.2024