Improved methodology for calculating the processes of surface anodic dissolution of spark eroded recast layer at electrochemical machining with wire electrode
Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
Подобные документы
Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016Investigation of the surface layer structure at high resolution. Study of surface morphology of treated detail. The use of electric-surface alloying components operating under conditions of friction and abrasionerosion wear and their restoration.
статья, добавлен 22.03.2016General characteristics of the hydrostatic spindle for ultraprecision double-sided machining. Familiarity with the main features and problems of modern engineering development. Consideration of ways to ensure quality indicators of machining parts.
статья, добавлен 20.07.2020Studying of sensor-transistor which based on a novel electrochemical transducer concept printed electrochemical sensors on paper. Consideration of electrochemical transistors which base their function on electrochemical modulation of the active material.
учебное пособие, добавлен 17.08.2014Comparison of two non-conventional processes which are laser and photochemical machining. The formation of complex shapes in metal sheets. Chemical etching of the material for the manufacture of the desired finished product by a controlled corrosion.
статья, добавлен 03.12.2015Defining of dimensional relationships where the aspect ratio. The building process for 3D microdevices. The features of creation surface energy high enough to maintain adhesion of the electroplated material until completion of the plating process.
реферат, добавлен 16.04.20173D printing (Additive Manufacturing Process, AM) is any of various processes used to make a three-dimensional object without the use of dies, molds or machining. The most basic, differentiating principle behind 3D printing. General principle modeling.
статья, добавлен 20.02.2019Surface-polymer flooding (the so-called micellar polymer flow) as a potentially advanced oil recovery technology is more effective than polymer flooding. Surface-active interaction and compatibility of the polymer. Distinctions, drawbacks of the method.
статья, добавлен 06.05.2018The use of metallic pigments with features of the geometry of the surface of printing materials. Functionality of the "Materials Editor" program and a group of parameters of geometric surface structures. Assessment of surface structures in the 3D system.
статья, добавлен 12.06.2023Grinding machine and its use for finishing workpieces, which must demonstrate high surface quality and high accuracy of shapes and sizes. Roughing operations in which grinding removes large volumes of metal fairly quickly. The components of machine.
статья, добавлен 10.03.2019The use of the boundary values of parameters of mould displacement of the earth's surface and refining the workings of the design scheme to predict the trajectory of sedimentation. Determination of empirical coefficients of mathematical equations.
статья, добавлен 30.07.2016Analysis of the development of the basic methods of engineering the contact surfaces of tribological systems. Characteristics of the problems and prospects of development of technologies of creating surfaces of discrete-oriented structure of the system.
статья, добавлен 18.02.2016Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016Methods of the equation of the cutting edge in the absolute coordinate system. A helix - a trace of movement of the cutting tool along the workpiece. Characteristics of the mathematical model of the formation of the microrelief surface when grinding.
статья, добавлен 06.05.2018Directions of development of production technology of high-precision parts. Research in the field of management precision and quality parameters of the treated surface. Improvement of the technological process, equipment, instruments and devices.
статья, добавлен 06.12.2016- 17. The influence mechanism of ferrite grain size on strength stress at the fatigue of low-carbon steel
The study of the properties of low carbon steel. Methods of cold plastic deformation. The rationale for the recommended annealing temperature. Is the microstructure of low-carbon metal. The study of the conditions of plastic deformation of ferrite.
статья, добавлен 29.01.2016 The main factors of physical phenomena that accompany the process of power explosive effect for the development of new processes of metal processing. Industrial testing of facing technology by explosion of artificial surfaces of complex configuration.
статья, добавлен 19.02.2019The base of constructing computer model of the analysis of complex physical-chemical phenomena in the process ORIEN in continuous arc furnace is as the main aggregate of energy-metallurgical complex. A mathematical model of physical-chemical processes.
статья, добавлен 02.11.2018The concept and functional characteristics of diamond-like films of amorphous carbon with a high concentration of carbon with SP3. The peculiarities of their practical use. Diagram of the coating, its physical and chemical properties, the benefits.
статья, добавлен 12.06.2015The study of the influence of the surface hardness of the auger on its wear during dehydration of solid waste in the garbage truck. Usage of the method of regression analysis, the logarithmic dependencies of auger wear depending on the hardness.
статья, добавлен 23.06.2022The analysis of fire-resistant intumescent coatings, which are currently used in Ukraine and abroad, as well as prospects for the development of new intumescent coatings with improved properties, is carried out. Methods of fireproofing metal structures.
статья, добавлен 13.11.2023Solution of the problem of the theory of elasticity for a composite in the form of a half-space with a thick-walled round cylindrical tube and a layer rigidly attached to the surface of the half-space. Assessment of the stress state of the composite.
статья, добавлен 26.02.2021Using and improvement of qualities of products of oil processing. The process of obtain a water-soluble colloidal sulfur with seating stability, good solubility in water, high biological activity. Selection of conditions to receiving polymeric products.
статья, добавлен 11.03.2019Offered and analysed of the method of calculating the operating parameters of warping spools and mode of winding. A formula that is obtained allows to define relationship between the parameters of the threads wound on a warping spool and their pull.
статья, добавлен 29.11.2016