Experimental research on heat dissipation at the hot end of semiconductor refrigeration chips
Analysis of TEC1-12705 and TEC1-12706 semiconductor refrigeration chip types with different hot heat dissipation conditions. Heat pipe heat dissipation test device for radiators. Effect of hot end heat dissipation conditions on cold end temperature.
Подобные документы
Character of force of friction is investigated and set in nominally-immobile connections on the stage of nominal adhesion and to passing to skidding. The capacity of connections are given by the method of coating on the basis of fusible to the alloy.
статья, добавлен 27.07.2021Establishing conditions for quality surface finish in grinding abrasive wheel. Determine the optimal mode grinding, allowing you to get the highest performance and lowest cost processing, providing the necessary tech-tech requirements for machine parts.
статья, добавлен 14.09.2016Review trapping processes in so-called “free” thick-film structures based on spinel-type Cu0.1Ni0.8Co0.2Mn1.9O4 ceramics. Studies need to add glass in the ceramic material. Positron trapping processes in temperature-sensitive thick-film structures.
статья, добавлен 30.07.2016- 79. The evaluation of snowdrifting simulation by snow and wind tunnel for urban design in winter cities
Factors of snowfall and wind load. Simulate snow and wind with wind tunnels that allow you to define the quality of city plans to reduce the impact of weather conditions. Computational fluid dynamics of snow drifts, its application in urban planning.
статья, добавлен 04.10.2021 Study of problems the sufficient conditions for the existence of solutions of linear nonhomogeneous impulsive boundary value problems with small perturbations when generating boundary value problem of impulsive has solutions for arbitrary right-hand side.
статья, добавлен 30.01.2017The system of rest is energy-saving, with power supply from alternative energy sources intended for complex recovery of an organism in house conditions. Determine the effectiveness of panel modules on the level of stress. Application panel "Ananta 2016".
статья, добавлен 19.12.2017Gathering of materials about a petroleum industry in a museum creates favorable conditions for their protection. The assemblage of materials is stored In a museum about the factory "Brothers Nobel". The oil extracted by brothers Nobel in 1894-1903.
статья, добавлен 03.03.2018Definitions and models of control in water supply and sanitation industry. Concession model of control sanitation industry in international practice. Condition of networks and evolution of model. Research limitations and future research directions.
дипломная работа, добавлен 13.11.2015Investigation of the surface layer structure at high resolution. Study of surface morphology of treated detail. The use of electric-surface alloying components operating under conditions of friction and abrasionerosion wear and their restoration.
статья, добавлен 22.03.2016Economic and social challenges of breakthrough technologies in the context of Industry 4.0, Industry 5.0, their impact on sustainable development. Technologies for creating the Internet of Things. Potential characteristics of disruptive technologies.
статья, добавлен 30.11.2020Adding ginger extract to the technology of table margarine production. Expanding the margarine market range and extending its shelf life. The effect of adding an additive on an organoleptic characteristics of margarine, giving it a spicy taste and aroma.
статья, добавлен 14.12.2024The conductive nanocomposite films based on functional reactive copolymers and bifunctional alcohols. Creation multiwall carbon nanotubes. Dependence properties of the nanocomposites from the specific composite composition and obtaining conditions.
статья, добавлен 30.07.2016Development of improved methods of calculation to quantify the anodic dissolution process began. Determining factors of electrochemical dissolution of the surface layers of steel, obtained at different process conditions electroerosion machining.
статья, добавлен 30.07.2016The adapted pitch concept involves varying the pitch and the length of the cutting portion as a function of the taper of the instruments. HEROShapers used to prepare and enlarge the coronal and middle thirds of the canal. The removal of dentinal chips.
статья, добавлен 10.12.2013Study of field distribution in structures such as a gold lattice, a graphene layer, and a silicon substrate. Conditions of maximum electromagnetic field distribution by these structures for the purpose of using them in photonics and electronics devices.
статья, добавлен 24.02.2024Influence of the type of machining and tool material on the structural state of the surface layer of steel during machining. Advantages of turning with composite 10 incisors compared to grinding. The occurrence of tensile stresses during metal processing.
статья, добавлен 14.09.2016Research of new ecological and energy-saving methods of food processing. Analysis of biotechnological processing of food using enzymes of proteinases, glutamine transferases, galactosidases, enzymes of extremophilic and psychrophilic microorganisms.
статья, добавлен 15.09.2022Analysis of the main causes of destruction of adhesive joints. Structural and technological stress concentrators, because of which cracks develop during operation. General characteristics of the resistance of adhesive bonding to failure at all stages.
статья, добавлен 30.04.2018The study investigates the kinematics of robots with the aim of expedient use of certain engineering solutions solving certain problems related to the accuracy of robot movement. The object of study is various types of robots and their kinematic systems.
статья, добавлен 20.07.2024Research microstructure Rodent dental alloy based on Ni-Cr-Mo after casting in a vacuum furnace. Chemical analysis of crystallographic orientation and topography. Bold molybdenum carbides, eutectic-P and particles of aluminum oxide within dendrites.
статья, добавлен 23.02.2016The role of coke gas cleaning in ensuring optimal operational productivity and compliance with environmental requirements in coke production. The influence of configurations and optimization of nozzle placement strategies on the quality of coke gas.
статья, добавлен 17.06.2024Huge gaps in structure and performance between different types of engines. The types and performance of modern advanced aero-engines, their practical applications in various aviation fields, and the development direction of future aircraft engines.
статья, добавлен 04.09.2024The types of mechanisms turning and folding blades used for power control and stabilization of frequency of rotation of the wind turbines. The dependence of the displacements of sliders and centrifugal weights on the angle of rotation of the blade.
статья, добавлен 14.09.2016Analysis of new scientific and technical knowledge about the nature of the origin of precious stones and their synthetic analogues and imitations. Review of existing technologies, modern devices for diagnostics of jewelry with inserts of precious stones.
статья, добавлен 11.11.2021Implementation of new neurotechnologies. Research of the concept of science, foresight and policy interlinking. Analysis of russian neurotechnology case. Identification and characterization of the main needs for improvements and changes in Russian case.
магистерская работа, добавлен 04.09.2016