Numerical simulation of viscoelastic materials
The developing of the numerical model of viscoelastic material using finite element method. The comparison of the obtained results with use of FEM software with experimental data. The calculation of the stress and strain state of the asphalt specimen.
Подобные документы
Learning algorithm of consistent actions to obtain quality coatings made by the complex technological method electrocontact strengthening of sprayed coatings. Analysis Ishikawa diagram which allows identify the causes of the impairment coatings obtained.
статья, добавлен 29.01.2016Model for calculation of nominal stresses in characteristic points of the surface fatigue crack to the tubular shaft in bending with rotation. Reasons for the decrease of the propagation velocity of cracks in the center and changing the geometry.
статья, добавлен 28.09.2016The mode of longitudinal motion of attached underwater vehicles under the action of propulsors is considered. Analysis of experimental data of design variants of models and natural objects. The behaviour of the devices in the aqueous environment.
статья, добавлен 15.02.2021Experimental researches of improvement of technology of preparation of preparation Torasemide 5 mg / ml a solution for injections, a choice of a filtering material. Aseptic production conditions using sterile filtration and thermal sterilization.
статья, добавлен 01.12.2017Transit of natural gas along the territory of Ukraine to the countries of the Western and Central Europe. Main resons of the loss of pipeline efficiency. Necessity for studying of the operation modes of the gas transport system during underloading.
статья, добавлен 01.12.2017The way which will permit to combine existing software products in an integrated computer-aided design system for the design of given plant. Unified operations dialog interaction kernel environment and a textual description dialogue procedures.
статья, добавлен 14.09.2016The method of reducing costs and increasing the strength of threaded joints, which are currently used in every field of human activity. Experimental research on the relation between thermal treatment and strength of adhesively sealed joints was con
статья, добавлен 28.09.2016Consideration of lightweight aggregate that obtained from the raw material modified by clay minerals, zeolites. Protection the environment from petroleum substances. Modification of the lightweight aggregate with the use of spent zeolite sorbents.
статья, добавлен 24.02.2016Developing of a photobioreactor design for wastewater treatment in which the application of new connections reduces material consumption for the manufacture of transparent flexible tanks, reducing labor costs for installation and dismantling of tanks.
статья, добавлен 10.07.2022Analysis of the scientific foundations of the development and implementation of raw material and product traceability systems in bakery production. Outline and scientific justification of measures for organizational improvement of product traceability.
статья, добавлен 04.09.2023Research of mathematical model of the process intrusion forming polymer products. Establishing a dependency on the angle of melt costs lifting screw injection unit in the material cylinder based on the geometric parameters of extrusion head and mold.
статья, добавлен 18.02.2016An experimental study of backscattering factor for a linear accelerator Siemens Oncor Impression Plus for photon energies of 6 and 18 MV with asymmetric radiation fields. Development and implementation method for determining the backscattering factor.
статья, добавлен 29.07.2016The main production methods jet fuels rocket engines. Prospects for the use of various raw materials to produce jet fuels in the context of limited energy resources. The impact of processing production and use of aviation fuels on the environment.
статья, добавлен 23.02.2016Square Lead-Rubber Bearings with four lead plugs to round Lead-Rubber Bearings with one lead plugs and shorten the analysis time. Comparison of load-deformation relationship. Comparison of the change in the outer edge temperature of the laminated rubber.
статья, добавлен 10.10.2021Development of a managed system architecture with the possibility of full-scale parametric optimization. Systematization of the architecture of the conversion system by the example of the technological process of liquid heating. Software designer EFFLI.
статья, добавлен 30.10.2016Algorithm for determination of transfer function models for transient processes from noisy data with continued fraction approximations is proposed. Presented method allows to solve the stability problem of low-order continued fraction approximations.
статья, добавлен 26.06.2016Familiarity with the basic method of identification of defects of the drive with induction motor using wavelet transform for the test signals. Analysis of a neural network model converted to the next subsequent stages on the basis of the algorithm.
статья, добавлен 28.08.2016Improving the method of dynamic analysis of mechanical systems dynamic factors dynamic model which can be represented by three-mass system of row with the first driving mass with prestressing elastic drive connections. Finding the dynamic coefficients.
статья, добавлен 30.07.2016An analysis of demand in the semiconductor industry, covering all three phases of materials: gases, liquids and solids. The study of the peculiarities of application for solids which includes a semiconductor substrate, metal, dielectric, an organic film.
книга, добавлен 14.03.2014Carbon nanotube diodes as part of nanotechnology and a key component of the nanotechnology revolution, which could have major implications for the future. Nanotechnology is a discipline that deals with the design, production and manipulation of materials.
статья, добавлен 19.03.2024These developments are devoted to the use of sol-gel processes in various branches of science and technology. Based on inorganic ion-exchange materials, a technology was developed to extract lithium from natural brines, which are poor in lithium content.
статья, добавлен 31.10.2017Description of main activities CAE Partner GmbH аn Enterprise of the MSC Group, foundation of the company and development of its in Europe. Software-products, services and the scope of production activities, which use technology developed by the company.
презентация, добавлен 21.02.2014The use of metallic pigments with features of the geometry of the surface of printing materials. Functionality of the "Materials Editor" program and a group of parameters of geometric surface structures. Assessment of surface structures in the 3D system.
статья, добавлен 12.06.2023Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016Types of tool materials: from high-carbon steel to ceramics and diamonds, and their use as cutting tools in the modern metal industry. Cutting tool and its characteristics: hardness, strength. Achieving an acceptable tool life before replacing it.
статья, добавлен 26.04.2019