Numerical simulation of viscoelastic materials
The developing of the numerical model of viscoelastic material using finite element method. The comparison of the obtained results with use of FEM software with experimental data. The calculation of the stress and strain state of the asphalt specimen.
Подобные документы
Research process to ensure the values of the endurance limit of the material details. The establishment of correlations between the modes of machining, quality of the surface layer and the fatigue limit. The characteristics of processed material.
статья, добавлен 14.09.2016Types of tool materials: from high-carbon steel to ceramics and diamonds, and their use as cutting tools in the modern metal industry. Cutting tool and its characteristics: hardness, strength. Achieving an acceptable tool life before replacing it.
статья, добавлен 26.04.2019The study of magnetron sputtered coatings on base AlN-TiB2(TiSi2). The structural composition, morphology coated materials. Features amorphous-like coatings AlN-TiB2(TiSi2) after annealing and their impact on physical and mechanical properties changes.
статья, добавлен 30.07.2016Gathering of materials about a petroleum industry in a museum creates favorable conditions for their protection. The assemblage of materials is stored In a museum about the factory "Brothers Nobel". The oil extracted by brothers Nobel in 1894-1903.
статья, добавлен 03.03.2018Information about the general state of technologies for the utilization of secondary energy resources and environmental resources. The essence of phase transitions in food production technologies. The possibility of creating energy-material circuits.
статья, добавлен 10.06.2022Проведение анализа применения технологии Big Data в поле цифровой экономики, необходимость рассмотрения правовых, этических аспектов осмысления применения данной технологии. Возможные риски, связанные с последствиями тотальной цифровизации общества.
статья, добавлен 27.03.2022Establishment of rational technological modes of processing various types of meat raw materials by needle injection on a multi-needle brine injector. Improvement of technologies and types of specialized equipment for injecting meat raw materials.
статья, добавлен 20.07.2024- 83. Structural and electro-physical properties of heterogenous film materials based on refractory metals
Structural phase composition analysis of heterogenous film materials based on refractory metals is presented. A thermal activity nature of their conductivity was determined. Of investigation were estimated thermal resistance coefficient and energy.
статья, добавлен 30.07.2016 The model is based on a regional convolutional neural network architecture that can identify and classify different types of damage, including those caused by natural disasters, accidents, or deliberate warfare attacks, such as shelling and bombardment.
статья, добавлен 12.12.2024The model is based on a regional convolutional neural network architecture that can identify and classify different types of damage, including those caused by natural disasters, accidents, or deliberate warfare attacks, such as shelling and bombardment.
статья, добавлен 12.12.2024Defining and analysis the essence of robot is an automatic device, which has a manipulator – mechanical analogue of human hand, and manipulator control system. Consideration and characteristic of the structural features model of domestic robot–helper.
статья, добавлен 29.01.2016Evaluation of the technical system and its subsequent use for decision-making to ensure complex technical systems with appropriate quality of work. The characteristics and specificity of the model changes performance States based on the Markov chain.
статья, добавлен 29.01.2016Wind turbine concept with air duct. Influence of the exit area and entry area on aerodynamic characteristics. Designing a new model of Invelox. The need to install a curtain at the end of the air intake to change the direction of the air flow up, down.
статья, добавлен 08.03.2021Consideration the vibroactivity in the refined dynamic model of the mandrel bar. An acoustic positioning system of screw-rolling mill. The study of dynamic processes in the tube. Mathematical model of vibroactivity of screw-rolling mill mandrel bar.
статья, добавлен 30.01.2016Особенности применения SPH-метода (Smoothed Particle Hybridization Method) для моделирования взаимодействия шин сверхнизкого давления с растительным покровом. Значения ширины шин для средств химизации при работе на почвах с низкой несущей способностью.
статья, добавлен 28.09.2016Various kinds of mathematical models of a snakelike robot motion depending on gait pattern. Simplified model of a snake. The motion sequence of three-mass system. The average velocity depending on number of masses. Determination of optimal masses number.
статья, добавлен 27.08.2020Definitions and models of control in water supply and sanitation industry. Concession model of control sanitation industry in international practice. Condition of networks and evolution of model. Research limitations and future research directions.
дипломная работа, добавлен 13.11.2015The model of spatially distributed curing process of epoxy matrix polymeric composite. The model using the projections of Pareto points set on the 8-dimensional space of design variables. Сontrol synthesis for the closed mould curing of composite spar.
статья, добавлен 30.05.2017Determination of a fire area during the time of its unobstructed development, the amount of the devices for the fire extinguishing agent supply. Consideration features of its mathematical model of the optimization in the woodworking enterprises workshops.
статья, добавлен 20.11.2014Characteristics of mathematical model of dynamic processes that occur in frictional hardening of flat surfaces of machine parts with use of the tool with the cut transverse grooves on its working parts. Cyclic circuit of the machine’s oscillations.
статья, добавлен 14.09.2016Расчет элемента трубопровода при помощи Flow Simulation в пакете SolidWorks. Характеристика исследования влияния размеров и формы воздуховодов на равномерность воздушного потока и сопротивление в вентиляции системы охлаждения тяговых электродвигателей.
контрольная работа, добавлен 17.09.2015Інформаційний аналіз методів та технологій для попередження утворення та видалення асфальтеносмолопарафінових відкладень на нафтогазопромисловому обладнанні. Дослідження віртуальної моделі струминно-кавітаційного генератора за допомогою модуля Simulation.
автореферат, добавлен 23.10.2018The roller of the belt as the most important parts of the conveyor, being subjected to continuous stress both during operation and in stopping periods. Causes and weight percentage of failures due to fatigue. Sealing system with simple labyrinth.
статья, добавлен 27.12.2016Renewable energy is energy obtained from solar, wind, wave, geothermal energy, water and other renewable sources. At this time, processes that are constantly occurring in nature are used, and these resources cannot be exhausted as a result of human use.
статья, добавлен 14.02.2025Properties and structure of hydrocarbons. Types and communication aromatics. The nature of the relationship between the carbon atoms. The methods of extraction and processing of oil. The use of the rectification columns for fractionating of raw materials.
презентация, добавлен 30.06.2014